搜索资源列表
yaokong-NEC
- NEC遥控编码格式的遥控器的解码程序,比较好用,实验通过-NEC remote encoding format for the remote decoding procedures, more convenient, through experiments
只用一个管脚的C51解码NEC红外遥控码程序
- 独具一格，只用一个I/O资源就可测出常用的NEC格式IR 遥控码-a unique and use only one I / O resources can be used to measure the NEC format IR remote control code
ir-NEC
- 红外源码（NEC协议）遥控接收在此中断程序内完成,遥控码放在ir_da[]中
main
- 电源控制,NEC遥控IR接受,和IR模拟发送代码,
IR.rar
- 红外遥控解码程序，NEC标准均可用，已经可以在很多机种上得到应用,IR
RC6-NEC
- NEC与RC-6红外遥控解码，已测试成功。单片机晶振为22.1184，COM口读取代码。-NEC and decoding infrared remote control RC-6, have been tested successfully. MCU crystal is 22.1184, COM port to read codes.
IR_RECEIVE.rar
- C51写的红外遥控接收程序，遥控码规范为NEC规格。,C51 written procedures for receiving infrared remote control, remote control for the NEC code requirements specification.
work
- NEC标准遥控接收处理程序，OK的IIC通讯程序，51单片机定时中断程序-NEC Standard Remote Control Receiver processing, OK for IIC communication procedures, 51 MCU timer interrupt program
nec
- C写的 nec芯片的 红外遥控器的发射 解码程序 51单片机 -C write nec chip infrared remote control launching decoding program 51 MCU
ykshuma
- NEC 标准遥控解码程序,对62221,62222等芯片设计的遥控可以解码,程序仅供参考.-NEC remote control decoding standard procedures, 62221,62222, such as chip design can decode the remote control, procedures for informational purposes only.
nec
- 遥控器NEC码C51解码程序 可以接受遥控信号并显示遥控码-NEC remote control program codes C51 codec can accept remote control signal and display the remote control code
NEC_encode
- nec遥控编码介绍 -nec remote control codes introduce
NEC-K
- 用单片机制作的红外遥控器，可以遥控电视等,采用NEC编码方式-Produced with infrared remote control MCU
remote
- 红外NEC遥控接收和处理模块，在51上完全应用通过-NEC remote control infrared receiver and processing module
NEC
- 此资料为NEC 格式红外遥控编码文档，其中有编码格式的具体说明-This data format infrared remote control codes for the NEC documents, which specify the encoding format
4路可学习红外遥控定时插板
- 4路的，可以学习任意NEC编码遥控器的按键，4路分别定时开关。有PCB文件。
NEC
- 用NEC红外遥控通过51单片机控制四位数码管，数码管为TM1637四位数码管显示模块(With NEC infrared remote control, through 51 SCM control four digital tube, digital tube for TM1637, four digital tube display module)
C51接收32BIT—IR
- 利用51定时器中断为125US接收NEC红外遥控接收，并且接收完毕作处理。(With 51 timer interrupts, the NEC infrared remote receiver was received by the 125US, and the processing was received.)
Main
- 通过串口发送指令发出RC5，NEC协议的红外信号(ending an instruction from a serial port to send out the infrared signal of the RC5, NEC protocol)
遥控-原码
- “HD26高清播放板”，红外遥控(采用NEC协议，PT2222 芯片的方式)控制， 改成语音控制, 用标准VUI模块V280板输出口，语音识别后，直接输出红外遥控发射编码到，HD26的IR口控制播放节目(The HD26 HD player is controlled by infrared remote control (NEC protocol and PT2222 chip). It is changed to voice control. The output port of the