搜索资源列表
8051 Timer 1 Mode 2 Example Program
- 8051单片机的定时器1的控制程序，通过调用这个程序很容易实现对定时器的操作-8051 of a timer control procedures, by calling this procedure is easy to achieve the right to operate the timer
timer.rar
- 此程序是C8051F120的5个定时器程序的集合，每个定时器的功能齐全。与此单片机的串口并用设置波特率时，串口1只能用定时器1，而串口0可以用定时器1234.,This procedure is the 5 timers C8051F120 collection procedure, each timer functions. With this single-chip serial port and baud rate settings, the serial port 1 can only
thread timer (D7)
- This component has the same functionality of the default Timer component, but it provides a higher resolution, until a maximum of 1 milisecond.-This component has the same functionality of the default Timer component, but it provides a higher resolu
led(10-1)
- DSPF2812学习程序： 描述:利用GP定时器1在GPIOF8引脚上产生方波，令一个贴片LED闪烁 系统时钟150M，高速外设时钟25M，128分频后定时器周期为5.12us,适于初学者学习-DSPF2812 learning process: Descr iption: Using the GP Timer 1 GPIOF8 pin to generate a square wave, so that a flashing LED chip system clock 150M, high
EggTimer-1.1
- Timer application used to show the use of timer in c#..net
timer
- 关于C#中timer类 在C#里关于定时器类就有3个 1.定义在System.Windows.Forms里 2.定义在System.Threading.Timer类里 3.定义在System.Timers.Timer类里 -The timer on the C# class in C#, there are three categories on the timer 1. Defined in the System.Windows.Forms in 2. System.T
1
- ATMEGA48 定时中断点灯，每一秒亮一次，一次持续30MS-ATMEGA48 timer interrupt lighting, light one every second, a continuing 30MS
timer
- NXP1768 处理器下采用C语言编写定时器0和定时器1的源代码-NXP1768 processor using C language source code of Timer 0 and Timer 1
timer
- AVR单片机的定时器模块驱动程序 包括定时器0和定时器1的使用 M16单片机 使用ICCAVR编写-AVR MCU timer module drivers include Timer 0 and Timer 1 ICCAVR prepared using microcontroller using M16
Practical-timer
- 同时用两个定时器控制蜂鸣器发声，定时器0控制频率，定时器1控制同个频率持续的时间，间隔3s依次输出1，10，50,100，200,400,800,1k（hz）的方波。 为了保证定时的准确性 晶振选择12M-The same time with two buzzer timer control, timer 0 control frequency, Timer 1 control with a frequency of duration, interval 3s sequentially outp
Using-T2-timer
- 使用T2定时器实现1秒精确定时__附有C程序_和汇编程序-Using T2 timer, 1 second precision timing
Timer-1---PIC
- Ejemplo realizado en CCS y simulado en Proteus para el uso del Timer1 (timer de 16 bits).
timer-control
- 定时器实现每隔1秒LED亮灭变化用定时器1工作方式2、定时时间改为0.5秒实现-Timer to achieve every second LED light out change with the timer 1 working mode 2, time to 0.5 seconds to achieve
timer-1
- 定时器产生精确延时，控制电平持续时间从而产生脉冲 ，简单易懂，有protues电路仿真，使用初学者。-The timer generates a precise delay, controls the duration of the duration to produce pulses, is easy to understand, has protues circuit simulation, and uses beginners.
8-Timer-1-Counting-Modes1
- example timer 1 stm8s micro
46-定时器1
- 46-定时器1(46- timer 1)
TIMER-1
- STM32 timer程序例程，经过测试了的(stm32f103 timer test , Data processing between forwarding)
Timer
- 本程序示例如何使用C语言写TIMER。头文件 misc.h有3个有关时钟操作的函数：1. timer_on() 2. timer_off() 3. timer_set(unsigned int, unsigned int,int)(This program illustrates how to use the Timer in 'C'. The header file misc.h has the three functions related to Tim
TEST1
- 1．在使用 12MHz 晶振的条件下， 晶振的条件下， 由 80 51 内部定时器 1按方式 1工作，即 作为 16 位定时器使用，每 位定时器使用，每 0.05 秒钟 T1 溢出中断一次。 P1 口的 P1.0P1.0 ～P1.7P1.7 分别接发光二极管的 L1 ～L8 。（用连线接 J2 、J3 ）。 要求 ：编写程序模拟一循环彩灯。变化花样为： 编写程序模拟一循环彩灯。变化花样为： ①L1 、L2 、…L8 …L8 依 次点亮； ②L1 、L2 、…L8 …L8 …L8 依次熄 灭；
TIMER 1 COMPARACION
- timer counter1 de microcontroladores