搜索资源列表
ADC_termoSensor
- adc convert for sensor in lpc2103
wavplayer.rar
- 基于LPC2103的WAV播放器的制作资料,Based on the LPC2103 in WAV player, making the information
ENC28J60.rar
- LPC2103以太网口开发模块的所有例程源代码,LPC2103 Ethernet port development module source code for all routines
RTC_TM1629
- philips LPC2103 ARM7 + TM1629C,利用SPI接口驱动TM1629C，来显示LPC2103 自带RTC时钟的驱动代码，用11.0952M晶振。完全调试OK-philips LPC2103 ARM7+ TM1629C, the use of SPI interface driver TM1629C, to show the RTC clock LPC2103 own driver code, with crystal 11.0952M. Full debugging OK
EINT
- philips LPC2103 ARM EINT0 EINT3的向量中断试验程序，P0.16为中断EINT0低电平中断，P0.14中断EINT3低电平中断，当不同的中断产生是P0.17和p0.18产生不同的PWM信号。-philips LPC2103 ARM EINT0 EINT3 vector interrupt the test procedure, P0.16 for the low-level disruption EINT0 interruption, P0.14 low EINT3
ADC
- philips ARM7 lpc2103 的AD口接光敏电阻，来探测LCD背光是否打开，并通过UART0，打印出AD转换后光米电阻测试的电压值，并输出LCD给光的开关状态-philips ARM7 lpc2103 I received the photo resistors AD to detect LCD backlight is turned on, and UART0, print optical AD conversion of the voltage meter to test the
lpc2103Library1
- philips arm7 lpc2103的常用功能的库函数上，并有库函数说明导读，绝对实用，由于文件太大，分上下两部分上传-philips arm7 lpc2103 function of the common library functions
lpc2103Library2
- philips arm7 lpc2103的常用功能的库函数第二部分，并有库函数说明导读，绝对实用，由于文件太大，分上下两部分上传-philips arm7 lpc2103 common feature the second part of the library functions and library functions that navigation is absolutely practical, as the file is too large, sub-From top to bot
DS18B20
- LPC2103 驱动 1 wire温度传感器DS18B20,独立供电当时,并用串口显示当前得温度值-LPC2103 drive 1 wire temperature sensor DS18B20, an independent power supply At the time, and a serial port displays the current temperature value
TOUCH
- Resistance touch screen control on ARM7 - LPC2103 (project in keil)-Resistance touch screen control on ARM7- LPC2103 (project in keil)
I2C
- 基于LPC2103的硬件i2c程序，硬件I2C中断方式软件包。-LPC2103-based hardware i2c hardware I2C interrupt procedure packages.
lpc2103
- clock, serial and lcd interfacer inplemented for lpc2103.
SPI
- Ejemplo SPI LPC2103, tiene un warning pero funciona
ICL7135
- 本系统采用NXP公司的ARM7处理器LPC2103为控制核心，实现智能电子秤的控制功能，原理图方案。-The system uses NXP s LPC2103 for the control of ARM7 processor core, intelligent electronic scale control functions.
LPC2103
- ARM7工程界面 ARM7PL2103-ARM7 ARM7 ARM7PL2103
ADC
- 本程序是的开发环境是IAR,以lpc2103为主控制器，可以采集外界0-3.3V的模拟电压转化为数字电压送给lpc2103处理，其分辨率是10为。-This program is the development environment is IAR, to lpc2103 based controller that can capture external 0-3.3V analog voltage into digital voltage sent to lpc2103 treatment,
I2C
- 本程序代码是在IAR环境中运行，核心芯片是LPC2103,LPC2103支持两个IIC总线接口，IIC总线接口可以用来传输数据，更可以用来保存上次掉电时的数据。-This code is in the IAR environment, the core chip LPC2103, LPC2103 supports two IIC bus interface, IIC bus interface can be used to transfer data, but also can be used
LCD
- 本程序代码在IAR环境中运行，其主控芯片是LPC2103，通过LCD与LPC2103的连接电路，可以实现在液晶屏上显示汉字字符等-The code runs in the IAR environment, its main chip is the LPC2103, and LPC2103 LCD connection through the circuit, can be achieved in the LCD screen to display Chinese characters, etc.
Virtual_UART
- LPC2103串口通讯程序，可使用Proteus联调来观察结果-LPC2103 serial communication program can be used to observe the results of Proteus FBI
SPI
- 在LPC2103实现的SPI通信传输，使用ADS开发环境-It achieves the communication through LPC2103, depending on the ADS