搜索资源列表
PIC2
- 无刷电动车控制器C代码 PIC16F877电动自行车驱动系统 电动车双闭环程序，采用双闭环方式控制电机，以得到最好的zh转速性能，并且可以限制电机的最大电流-brushless electric vehicle controller C code PIC16F877 electric bicycle drive electric cars double-loop process, double-loop control motor, to get the best en speed p
dcmotorkaibihuancontrol
- 关于直流电机的开鼻环控制的c程序。 大家如果认为可以的话自己去好好研究一下，可以运行。-of DC motor control of open love for the c procedures. If we think it is possible to make good their study, can run.
CYJLAST8
- C8051F020开发应用程序，完成人机界面及IO的输入输出，包含8路AD模拟输入和2路DA输出，还有PWM驱动电机的控制。-C8051F020 development and application procedures, man-machine interface and complete IO input and output, AD contains eight analog input and two output DA Road, PWM motor drive control.
shiyongdedianjiqudongxitong
- 利用串口驱动步进电机的程序。该文件能够运行，请放心，当然要配置相关硬件最好！-use stepper motor driven procedures. The paper will run, please rest assured, of course, related hardware configuration best!
1231313131
- 利用C语言对DSP进行程序设计，驱动交流异步电机，这时使用的是SVPWM方式
sm3
- 一种串口+按键控制步进电机的c语言程序，可以按加速，减速键控制速度，按逆时针/顺时针键控制转向，按暂停键使步进电机暂停。-A kind of serial+ key control stepper motor c language program, can be speed up, slow down keys to control speed, according to counter-clockwise/clockwise shift key control, stepping motor
sadf
- 关于温度自控的C语言程序，电机PWM 控制-About the temperature-controlled C-language procedures, PWM motor control
main
- 单片机驱动异步电机的C语言程序，驱动两个电机，经测试可以使用，非常完整-Induction motor-driven single-chip C-language program, drive the two motors, the test can be used by the very integrity of the
51pwm
- c语言编写51单片机产生PWM的程序和怎样控制直流电机-c language program 51 MCU and how to generate PWM control of DC motor
Code
- dsp例子程序，包括滤波器，FFT，电机控制等-dsp examples of procedures, including filters, FFT, motor control, etc.
C51DCMOTORPWMSPEED
- 51直流电机PWM测速程序keil编译C语言-51 DC Motor PWM Speed keil compile C language programs
bujidainji
- 用单片机编写的步进电机的程序 很实用 调试也通过了-Stepper motor with microcomputer programs written in a very practical test runs were performed
synchronousmachine
- 多回路法在故障诊断有着广泛应用，改程序是基于C++用多回路法计算凸极同步电机参数的函数。-Multi-loop method is widely used in fault diagnosis, changes are based on C++ with multi-loop method to calculate parameters of a salient pole synchronous motor function.
intellectual-car
- 简易智能迷宫小车的控制系统以STC89C52为核心，用一片L298N驱动两个减速电机。12V电源单独给电机供电，再用7805把12V电源降压至7V给单片机供电。小车的传感器模块感应壁障，并将壁障信号输入最小系统版，最小系统版根据程序设计的要求做出相应的判断送给电机驱动模块，让小车来实现前进、左转、右转、反转等基本功能。-Simple intelligent control system of the labyrinth car STC89C52 as the core, two geare
3
- 关于液晶12864，串口通信RS232，步进电机，数码管动态扫描，时钟程序，音乐兰花草的小程序，都是在CVI上开发的，好用。-On LCD 12864, serial communications, the RS232, stepper motors, digital tube dynamic scan clock program, small program of music orchids are developed on the CVI, easy to use.
bujindianji
- 步进电机程序，可以实现正转，反转，停止等功能，亲测过，很好用-Stepper motor program, can achieve forward, reverse, stop, pro-test before, easy to use
MFZ
- 控制电机程序，利用中断控制电机正反转以及速度-motor control
Descccp
- 可用于51单片机基本程序，表决器，定时器，步进电机(Can be used in 51 single chip microcomputer basic program, the meter, timer, stepping motor.)
触发程序文件
- 控制晶闸管的触发角，使单片机发出脉宽为30°的双触发脉冲波形，实现电机的起动。(By controlling the trigger angle of thyristor, the single-chip computer can send out a double trigger pulse waveform with a pulse width of 30 degrees to start the motor.)
解析仪压气泵程序
- 2024-01-05解析仪的进气口进行压气，使用的原理是利用电机的来回运动控制气泵的压气（关闭外接电磁阀，打开进气阀）和吸气（打开外接电磁阀，关闭进气阀），这样就能使解析仪自动的工作。