搜索资源列表
11_stepmotor.rar
- linux系统下 s3c2410 上的步进电机程序 ,linux system s3c2410 procedures on the stepper motor
vid29
- arm9，linux2.4，一个步进电机的程序-arm9, linux2.4, a stepper motor procedures
stepmotor
- 这是pxa270的步进电机驱动程序，测试功能完好，能加深对Linux内核的理解-This is the PXA270 stepping motor driver, testing features intact, can deepen their understanding of Linux kernel
linux_ad_da_motor_keyboard_tty
- Linux应用程序开发中的ad、da、串口、步进电机、键盘扫描的源码，希望对大家的linux系统开发有所帮助，一同学习，一同讨论。-Linux application development in the ad,da,serial port,stepper motor,keyboard scan source code,hope everyone help linux system development,with learning,to discuss them.
ftp628_printer
- 这是在LINUX2.6.28下的FTP-628的驱动.编入内核即可.应用程序一次送入两行点阵数据,384*2个点阵,因为步进电机一步需要两行数据.在硬件上,请自行处理MOTO信号,和STB信号.可能PIN要先对.本人运行过了.没有问题.-This is LINUX2.6.28 under the FTP-628 driver. Can be incorporated into the kernel. Once the application data into two rows of dot m
stepmotordriver
- 该程序是一个基于s3c2440的步进电机驱动程序和测试程序，编译内核版本为linux-2.6.13。-The program is a stepping motor based s3c2440 drivers and test program, compile the kernel version is linux-2.6.13.
stepmotor.tar
- 步进电机的驱动程序，可以进行频率设置，占空比设置。-Stepper motor driver can set the frequency, duty cycle settings.
LinuxDriverForStepper
- 步进电机在Linux的驱动程序，CPU为S3C2410-Stepper motor driver in Linux, CPU to S3C2410
MotorDriverAndApplication
- 这是linux下步进电机的驱动程序（分别适合与电机连接到IO口与连接到中断或总线的情况），并分别附有相应的上层应用程序，可以用来测试驱动。-This is under linux stepper motor driver (for, respectively, with the motor connected to the IO port and interrupt or bus connection to the case), respectively, with corresponding
aaa
- 在数控原代码开发过程中提出了步进电机正反转控制的实现方法,并根据此方法,给出了其相应的实现程序。 -very good.
STEPMOTOR_L298DRVtest
- 用于L298N的交流电机驱动，本代码用于步进电机正传两相八拍的程序。-For L298N AC motor drive, the code for stepper motor True Story of two-phase eight-beat program.
STEPMOTOR_L298DRVtest
- 用于L298N驱动控制步进电机，本代码是其中的两项四拍程序。-For L298N drive control stepper motor, the code is one of the two four-beat program.
rightMotorContr.c
- MicroMouse618上的右步进电机驱动时序优化程序，2013版本-On the right MicroMouse618 stepper motor driver timing optimization program, 2013 version
drivate
- 这是2410控制步进电机的驱动程序，仅供参考。-This is the driver it is trying to control a stepper motor
motor
- S5Pv210的步进电机程序，在Linux下直接编译即可下载到板子上，实现正转反转等功能-S5Pv210 stepper motor program, compiled under Linux can be downloaded directly to the board, and other functions to achieve forward reverse
stepermoto
- 供测试使用的四项五线步进电机的c语言驱动程序，使步进电机旋转两圈。-C language for test using four five wire stepper motor driver, the stepping motor rotates two circles.
Motor_control
- 供测试使用的二相步进电机驱动程序（胶水）-Phase step for testing the use of stepper motor driver
Gcode_executer
- 供测试使用的G代码执行程序，供二相步进电机。-For testing the use of G code program execution, for two-phase stepper motor
Bipolar_Stepper_Motor_Class
- 供测试使用的二相步进电机驱动程序，配合g代码的使用。-Phase step for testing the use of stepper motor driver, and with the use of G code.
BUJDJ
- 51单片机控制步进电机的简单程序，主要学习51单片机怎么控制步进电机的转动。-51 SCM stepper motor control simple program, mainly to learn how to control rotation of 51 single-chip stepper motor.