搜索资源列表
异步电机PWM
- 变频器开发基础程序,这个针对异步电机控制系统!-converter development foundation procedures, the induction motor control system!
linux_udp
- 我自己写的udp服务程序，用于远程电机实时控制，包括client和server。编译通过运行正常。-I wrote it myself udp service procedures, for remote real-time control, including the client and server. Compiled by operating normally.
linux_motor_44B0
- 在博创的44B0开发板上做的一个电机控制的程序，经过了测试，运行良好。可用作最最新的新手学习哈。-in Bo Chong 44B0 development board to do a motor control procedures after the test, the operation is good. Most can be used to study the latest newcomers Kazakhstan.
11_stepmotor.rar
- linux系统下 s3c2410 上的步进电机程序 ,linux system s3c2410 procedures on the stepper motor
BLDC-driver
- linux2.4.18下基于s3c2410的电机控制器驱动程序的PWM驱动以及测试程序-linux2.4.18 Based on s3c2410 the PWM motor controller driver and test driver program
vid29
- arm9，linux2.4，一个步进电机的程序-arm9, linux2.4, a stepper motor procedures
stepmotor
- 这是pxa270的步进电机驱动程序，测试功能完好，能加深对Linux内核的理解-This is the PXA270 stepping motor driver, testing features intact, can deepen their understanding of Linux kernel
stepmotor
- 嵌入式LINUX步进电机驱动试验程序，可以配合ARM开发板或试验箱来实验-Embedded LINUX stepper motor-driven testing procedures
can
- 该程序是基于S3C2410通过CAN来实现两部不同实验箱的通信，从一部实现箱ad采集来控制另一部实验箱的电机，且具有QT界面。-The program is based on the S3C2410 through CAN to achieve two different experimental box communications, to achieve from a collection box ad another experiment to control the electrical
pasteco-20030108.tar
- Linux下电机驱动程序，驱动学习的好资料。该资源来源于互联网。-Linux under the motor drive, a good data-driven learning. The resource from the Internet.
linux_ad_da_motor_keyboard_tty
- Linux应用程序开发中的ad、da、串口、步进电机、键盘扫描的源码，希望对大家的linux系统开发有所帮助，一同学习，一同讨论。-Linux application development in the ad,da,serial port,stepper motor,keyboard scan source code,hope everyone help linux system development,with learning,to discuss them.
ftp628_printer
- 这是在LINUX2.6.28下的FTP-628的驱动.编入内核即可.应用程序一次送入两行点阵数据,384*2个点阵,因为步进电机一步需要两行数据.在硬件上,请自行处理MOTO信号,和STB信号.可能PIN要先对.本人运行过了.没有问题.-This is LINUX2.6.28 under the FTP-628 driver. Can be incorporated into the kernel. Once the application data into two rows of dot m
stepmotordriver
- 该程序是一个基于s3c2440的步进电机驱动程序和测试程序，编译内核版本为linux-2.6.13。-The program is a stepping motor based s3c2440 drivers and test program, compile the kernel version is linux-2.6.13.
stepmotor.tar
- 步进电机的驱动程序，可以进行频率设置，占空比设置。-Stepper motor driver can set the frequency, duty cycle settings.
LinuxDriverForStepper
- 步进电机在Linux的驱动程序，CPU为S3C2410-Stepper motor driver in Linux, CPU to S3C2410
io
- Linux下C语言实现IO接口的驱动程序，主要包括：数码管显示、电机驱动、按键驱动以及Led驱动。-IO interface for Linux drivers, including: digital control, motor drives, key drives, and Led driver.
MotorDriverAndApplication
- 这是linux下步进电机的驱动程序（分别适合与电机连接到IO口与连接到中断或总线的情况），并分别附有相应的上层应用程序，可以用来测试驱动。-This is under linux stepper motor driver (for, respectively, with the motor connected to the IO port and interrupt or bus connection to the case), respectively, with corresponding
motor
- S5Pv210的步进电机程序，在Linux下直接编译即可下载到板子上，实现正转反转等功能-S5Pv210 stepper motor program, compiled under Linux can be downloaded directly to the board, and other functions to achieve forward reverse
rspi_robot.tar
- python开发的树莓派智能小车源码 压缩包内有文件若干，其中final_test.py是最终程序，sensor.py是超声波测距模块的代码。解压后进入代码根据gpio引脚定义将电机驱动板连接树莓派的相应gpio引脚。（代码中有定义），接好后直接python finel_test.py，即实现小车的无人自驾驶-压缩包内有文件若干，其中final_test.py是最终程序，sensor.py是超声波测距模块的代码。解压后进入代码根据gpio引脚定义将电机驱动板连接树莓派的相应gpio引脚。（代
MCRP07_Library程序库
- 电机控制程序,文件清晰是一个很好的学习资料,供大家参考。(Motor control program)