搜索资源列表
arm_led_interrupt
- 在s3c6410上实现采用中断按键控制led灯点亮，裸板驱动(c语言)-to bright the led with c throght loop
cgi_led
- 实现了led灯的远程控制!这是其代码实现过程-led realize
led_driver
- led灯的驱动，仅仅实现了对其的亮灭控制。-led control
s5pc100
- 利用平台设备机制，对s5pc100实现按键对Led灯的控制，按下点亮，松开熄灭-Use platform equipment mechanism to realize s5pc100 buttons on the control of Led lights, press the light, loosen put out
leds-gpio
- 控制led灯的驱动程序，也就是流水灯，程序中有4个led灯，依次按照先后顺序亮与灭-Control driver led lights, light water, 4 led lights in the program, followed in accordance with the sequence of bright and off
key-and-led
- stm32的可用驱动模板，通过简单的按键控制流水灯来实现-the stm32 available driver templates, through the simple push-button control of light water
LED_driver
- 控制一个LED灯的驱动 开发板是S3C2440-Control an LED lamp driver S3C2440 development board
eduk4-key
- /** *summary：本驱动目的为按键控制LED灯的状态 *descr iption：Edkit-VI试验箱中有4个LED灯和2个按键 * 我们用按键1来循环选择你要控制的LED * 按键2来控制LED的状态 * 按键2的操作将在按键1选择的LED上执行 * 初始状态下选择的LED为亮 * 当你按下按键2后选择的LED变为闪烁状态 * 再按一下后选择的LED变为熄灭状态 *author： * * */ /-/ The
led_analog_traffic_light
- /** *本程序目的为控制LED灯模拟红绿灯 * 具体：Edkit-8试验箱中可以介入4个LED灯，但我们只用其中的3只 * 规定第1只表示红灯，每次亮20秒 * 规定第2只表示黄灯，每次亮5秒 * 规定第3只表示绿灯，每次亮20秒 *开始时红灯先亮，然后黄灯、绿灯依次亮。循环反复 *每次灯切换时会有3秒的闪烁时间 * * *gcc -o led_analog_traffic_light led_analog_traffic_light
csu_led
- LINUX 下对LED灯的控制的驱动程序-LINUX drivers under the control of the LED lights
LED
- RM9 2400开发板LED灯中断控制源码-failed to translate
4_key15_simple
- 这是一个键盘驱动，是在ARM上实现的，通过按键控制LED灯-This is a keyboard driver on ARM keys to control LED lights
gfds(2)
- 针对HC_SR501驱动的编程，主要是对LED灯的控制-For HC_SR501 driven programming, mainly for control of LED lights
17-platfrom_key
- FS_S5pc100按键驱动,基于platform的，在按键的同时还可以控制led灯得亮灭-FS_S5pc100 key driver based platform, and the keys at the same time you can also control led lights too bright off
LEDTesting2
- s3c2410 板上实现QT控制LED灯，实现LED灯一一对应的点亮也可实现随机点亮。此次设计为本科生字符驱动编写的程序，经过运行和检验完全正确，使用版本为QT4.6-s3c2410 board realized QT control LED lights, LED lights illuminate one correspondence can also be achieved randomly lit. The design for undergraduate programs writte
led_driver
- 基于mini2440的led驱动编程，可实现在终端上控制led灯的亮灭-Based on mini2440 led driver programming
tiny210_led
- 基于友善之臂Smart210 入门教程 ，led灯的控制驱动程序+应用程序-the LED control of Smart210
LED
- linux系统下LED灯采取中断形式GPIO控制-in linux LED lights take the form of an interrupt GPIO control
day01
- 通过操作GPIO口来控制LED灯状态的开关，刺猬驱动程序的代码！-By manipulating the GPIO port to control the state of the LED lamp switch, hedgehog driver code!
LED
- 点亮P1口的一个LED灯 该程序是单片机学习中最简单最基础的， 通过程序了解如何控制端口的高低电平-A leds light up P1 mouth The program is the basis of a microcontroller learning one of the most simple, Through the application to know how to control the high and low level of port