搜索资源列表
uart+lcm13
- 是用C语言编写的关于用51单片机控制12864液晶LCD的源程序，适用与交流电压及其谐波的显示
STC51-MCUs-communication
- 本程序实现了基于51单片机的多机串行通讯：通过主机对从机操作读取获得挂于从机的温度传感器DS18B20温度值显示于主机控制的液晶屏。-This program implements the serial communication based on 51 single-chip multi-machine: by the host to read from the operating temperature sensor DS18B20 temperature hanging slave T
gps1602.rar
- GPS＋sT单片机＋1602液晶显示源码,GPS+ sT-source single-chip LCD+1602
gps
- 使用AVR单片机解析出GPS数据，并将这些信息显示在1602液晶屏上-Using the AVR microcontroller parse out the GPS data and information displayed in the LCD screen 1602
GPS
- 单片机读取GPS传回的数据，解析后通过液晶显示出来。-Returned microcontroller reads the GPS data, parse through the LCD.
gps
- 51单片机通过串口接受GPS的信号，并在液晶1602LCD上显示。-51 SCM through a serial port accept GPS signal, and in the liquid crystal display on 1602 LCD
USBLCD
- 通过USB接口给单片机发送数据，然后单片机再将其显示在LCD上-To the microcontroller through the USB interface to send data, and then microcontroller and then display it on the LCD
GPSLCD
- GPS的信息液晶显示，单片机通过串口接收GPS数据，处理，在液晶显示器上显示出结果-GPS infomation show on the lcd .by com
GPS-system-MCU-display
- 接收GPS模块发送到单片机的信息，解码出时间、经度、纬度、卫星数量等信息，并在一块12864液晶上显示-Single-chip GPS module receives the information sent to the decoding of the time, latitude, longitude, number of satellites and other information, and an LCD display 12864
lcd
- 52单片机与PC机通信，通过软件助手给单片机发送数据，利用lcd屏显示数据-52 microcontroller and the PC communication software assistant to the microcontroller to send data using the lcd screen to display data
lcd12232F(ST7920)
- LCM12232F液晶驱动,从单片机发送一个字节的数据到液晶,在Lcd中显示16*16汉字 -The LCM12232F LCD driver, the SCM sends a byte of data to the LCD, display of Chinese characters in Lcd 16*16
SerialDisplay
- 串口连接16针LCD显示，单片机控制。可用RFID显示-Serial port to connect a 16-pin LCD display, single-chip control
UART_VHDLCodes
- 基于VHDL的异步串口收发器，在FPGA上设计Uart接收模块实现从pc接收串口数据； 在FPGA上设计Uart发送模块，把从pc接收的数据的16进制值加1再发送给PC； 设计单片机和FPGA接口模块，把接收到的数据送给单片机，并显示在LCD上 -VHDL-based asynchronous serial transceivers Uart receive module in the FPGA design from pc to receive serial data desig
TEL13796088061
- 在12864液晶上显示一行汉字单片机爱好者和TEL13796088061-In 12864 a line of Chinese characters shown on the LCD MCU lovers and TEL13796088061
TRX800M-SI4463-LM7029
- 单片机PIC16F1947+RFIC SI4463+LCD显示 的数字无线对讲机 控制程序 频率 915MHZ 输出 20DB 波特率50Kbps GFSK 调制幅度25KHZ-SCM PIC16F1947+RFIC SI4463+LCD display digital wireless radio frequency 915MHZ Output 20DB control program baud rate 50Kbps GFSK modulation amplitude 25KHZ
51-microcontroller-GSP-LCD-routines
- 基于51单片机Gps+12864液晶例程，显示当前位置时间，经纬度等等。-51 microcontroller Gps+12864 LCD routines
GPS-12864
- GPS模块通过串口向单片机发送固定格式的数据，单片机的串口接收到数据后，进行解析，在LCD上显示，包括：日期时间，经纬度，速度，角度，高度-The GPS module through the serial port to the microcontroller sends a fixed format data, the serial after receiving the data, analysis, display, including: the LCD date time, latit
uart
- 基于FPGA的一个异步串口收发器（UART）在FPGA上设计Uart发送模块，可以把从pc接收的数据的16进制值加1再发送给PC；设计单片机和FPGA接口模块，可以把接收到的数据送给单片机，并显示在LCD上。-Uart transmission module design on an FPGA FPGA-based asynchronous serial transceiver (UART), can be hexadecimal values from the pc
OLED显示(模拟SPI总线)2
- 单片机nrf82532驱动液晶屏,使用串口驱动程序，很好是节约单片机输出口。(The single-chip nrf82532 drives the LCD screen and USES the serial driver, which is very good to save the single chip.)
显示部分程序
- 此部分为将单片机运算的显示控制信号送制液晶显示屏的控制程序(This part is a control program that sends the display control signal of the single chip computer to the LCD.)