搜索资源列表
FPGA
- 本文介绍了一种新的使用串行通信进行DSP远程在线编程方法。对设计中的主要技术：DSP与PC机的串口通信、Flash编程以及DSP自引导等进行了详细介绍。结合TI公司的TMS320VC33处理器，阐述了具体的实现方法
FPGA与USB通信的测试代码
- FPGA与USB通信的测试代码，包括FPGA中的程序（Verilog编写）和PC机上的主控程序以及USB固件程序。,FPGA and the USB communication test code, including the FPGA in the procedure [Verilog prepared] and PC-control procedures, as well as the USB firmware.
uart
- 串口通讯 PC发送FPGA接受后回传 verilog语言-uart verilog
usb_VC
- usb数据采集-上位机程序vc完整工程（配合cypress的usb芯片使用）-usb data acquisition- complete PC vc program works (with the usb chip to use cypress)
usbFPGAconnect
- 该例程是PC机通过FX2-CY7C68013-A的USB2.0控制芯片与FPGA实现通信。其中的工程和代码包括PC机上的USB固件程序、驱动程序、上位机程序，FPGA上的VERILOG通信程序。-The routine is a PC, through the FX2-CY7C68013-A of the USB2.0 controller chip and the FPGA to achieve communication. One of the projects and code, incl
FPGA-RS232-verilog
- fpga上的串口驱动程序，包括接收主机来的数据（deserial）和发送由FPGA产生的数据(serial).该程序的调试需要借助串口调试助手-serial port driver on the fpga, including the receiving host to the data (deserial) and send the data generated by the FPGA (serial) to pc. The program needs the serial debug deb
Uartmodule
- 实现FPGA与PC机的串口通信功能，实现数据的收发。-FPGA with the realization of PC-serial communication functions to send and receive data.
feng_rs0
- 基于FPGA的串口通信，PC给FPGA发送数据，FPGA收到数据并返回给PC-FPGA-based serial communications, PC to the FPGA to send data, FPGA Receive data and return to the PC
RS232
- interfacing pc with FPGA for data communication-interfacing pc with FPGA for data communication
uatr_and_dds
- 实现通过PC来控制fpga发出波形，波的形状和频率可通过PC控制，波形利用dds来发出，这是当时我做的电子测量的课程设计。-Fpga implementation given by PC to control the waveform, wave shape and frequency can be controlled through the PC, waveform using dds to send, this is when I do the electronic measurement
CIS
- 程序主要实现EZ-USB的控制功能，加上BORD-CONTROL两个程序实现FPGA控制CIS图像采集程序的数据保存，并传输到PC机上进行数据保存-Program mainly realizes the ez-usb CONTROL functions, plus BORD CONTROL- two program CONTROL of CIS image acquisition program FPGA, and the data transmission to PCS data storag
PPI3
- 该设计完成线阵CCD数据采集任务，包括以下四个方面的内容，USB芯片固件设计，FPGA的驱动程序设计，USB驱动程序部分，PC客户端程序。USB芯片采用的事CY7638013A.-Linear CCD data acquisition tasks of the design is completed, including the following four aspects, the driver of USB chip firmware design, FPGA design, part of
UART
- fpga开发板与电脑进行串口通讯，实现了基于FPGA的串口接收发功能-fpga development board with a PC serial communications, FPGA-based serial port to receive hair
clk_test
- UART串口程序，将FPGA数据传到上位机上-UART program,transmitting data from FPGA to PC
UART_VHDLCodes
- 基于VHDL的异步串口收发器，在FPGA上设计Uart接收模块实现从pc接收串口数据； 在FPGA上设计Uart发送模块，把从pc接收的数据的16进制值加1再发送给PC； 设计单片机和FPGA接口模块，把接收到的数据送给单片机，并显示在LCD上 -VHDL-based asynchronous serial transceivers Uart receive module in the FPGA design from pc to receive serial data desig
test1_rx
- fpga实现串口数据通信，实现PC与目标设备通信-fpga control uart
USB-FPGA-communications
- CY7C68013-A实现PC机与FPGA的USB通信例程-CY7C68013-A USB communication routines between PC and FPGA
USB
- 此例程是基于FPGA的USB控制器实例，主要功能为通过FPGA芯片控制USB芯片，实现开发板和PC机之间的USB接口数据通信，来模拟一个硬件加密设备的功能。用Verilog语言实现。-This routine is an instance of the USB controller based on FPGA, the main function is to control USB chip by the FPGA chip, implement the USB interface for da
uart
- 基于FPGA的一个异步串口收发器（UART）在FPGA上设计Uart发送模块，可以把从pc接收的数据的16进制值加1再发送给PC；设计单片机和FPGA接口模块，可以把接收到的数据送给单片机，并显示在LCD上。-Uart transmission module design on an FPGA FPGA-based asynchronous serial transceiver (UART), can be hexadecimal values from the pc
test_ad_in
- 通过信号源给AD9220传输数据，并通过uart串口在PC上显示输入的数据(he data is transmitted to the AD9220 through the signal source, and the input data is displayed on the PC through the UART serial port.)