搜索资源列表
8255控制循环LED显示
- 一个采用8255芯片控制8个LED灯循环点亮的程序代码-a 8255 chip used to control eight LED lights lit circle code
chuankoubiancheng
- 串口编程--接收PC发过来的字符串,回发字符串.发送期间中断控制LED灯闪烁 采用外部晶振22.1184MHz 使用定时器1,方式2产生波特率,SMOD = 0或者1 定时器初值X=256-SYSCLK*(SMOD+1)(BAUDRATE*384) -Serial Programming -- receiving PC sent the string, the string back. During this interruption control LED lights exter
usb061
- 基于凌阳SPCE061A芯片的USB通讯可实现1.通过USB通讯，PC端应用程序能够控制LED灯的亮灭；2.PC端应用程序发送小于65字节的字符串给SPCE061A,SPCE061A接收PC发送的小于65字节字符串后将接收到的字符串发送给PC，PC接收字符并显示在界面。-based Sunplus SPCE061A USB chip can achieve a communication. USB communications, PC-side applications to control t
UARTLCD
- Zigbee无线网络节点的串口控制LED灯，附带详细说明，基于513X芯片，开发环 境为codeblocks
VC上位机控制单片机源码
- 一个小软件，用vc写的，上位机控制单片机LED灯亮灭的小软件。文件包括整个项目过程的上、下位机源码！
ApplicationControlLED
- 内有usb固件程序与上位机程序，通过上位机操作控制LED灯的显示-There are usb firmware and PC programs, operational control by the upper LED light display
CardreaderLED_Test
- 通过串口,来控制读卡器的LED灯,通过LED灯,来知道读卡器的各种状态.-Through the serial port to control the reader' s LED lights, LED lights through to know the various readers status.
LED_blinking
- LED灯的控制代码，书籍上的经典案例，好代码-LED control code
serial_control_led
- c51单片机编程。利用串口从电脑上向单片机发送数据，单片机接受并返回数据，同时控制单片机实验板上的LED灯。-c51 microcontroller programming. Using the serial port from a computer to send data to the microcontroller, microcontroller to accept and return data, SCM test panel LED lights.
controling-of-lights
- 下位机通过串口接收数据并降该数据作为switch语句变量对应到不同的函数产生相应的现象，例如当按下全亮按钮时，通过下位机程序控制LED灯使LED灯全亮。 当鼠标勾选单灯控制区复选按钮时，同理通过串口传输数据，相应的LED点亮，取消勾选后该灯熄灭。 当鼠标点击流水灯控制区某个单选按钮时，上位机将数据通过串口送至下位机，下位机根据数据相应调节流水灯延时函数变量，完成控制流水灯速度的功能。 -Lower computer through the serial port to receive
CRC16
- 通过CRC-16循环冗余校验的方式实现数据传输与控制，例如控制LED灯、蜂鸣器、发送数据到上位机-By CRC-16 cyclic redundancy check means to achieve data transmission and control, such as control of LED lights, buzzer, sending the data to the host computer
WR_CtrlLED
- USB控制LED灯的程序 包括USB设备的数据收发灯-USB LED light control procedures, including USB devices for data transmission light
URAT
- 一个简单的串口通信汇编程序，通过上位机发送控制信号控制单片机LED灯的点亮与否。文件有protues仿真电路与hex文件。调试时请下载串口调试助手，端口Com1，波特率96-A simple serial communication assembler, through the host computer sends control signals control the chip LED lamp is lit or not. Documents protues Simulation ci
the-test-about-USB-light-up-LED
- 一个通过USB端口去控制LED灯亮的MFC软件-A MFC software that can control LED lighter through USB port
V0.7
- 控制LED灯的小程序，本来为DMX512写的，现在改为一般串口控制-Control LED lamp of small procedures, originally written for the DMX512, now changed to general serial control
LED-control
- 单片机控制继电器的一个LED灯,可以控制继电器的LED的亮和灭-control one LED
led
- 使用型号为CY7C68013A的USB芯片，通过开发板上的按钮控制LED灯的状态-This directory contains the dev_io 8051 firmware The purpose of this software is to demonstrate how to use the buttons and LED on the EZ-USB developer s kit. The device I/O example program uses
地感LED灯程序485总线
- 地感七彩灯485双向控制。单片机485通信，RGB灯控制。(485 way bidirectional control of ground feeling colorful lamp.)
wifi控制LED灯副本
- 实现用手机控制ESP8266,用手机wifi控制LED灯的开和关.(Realize the use of mobile phone control ESP8266 to control ESP8266 and control LED lights with wifi.)
cc2530蓝牙 PWM 控制LED灯
- 使用cc2530模块， HC-06蓝牙模块， 通过手机控制，调节PWM 控制LED灯(Using the CC2530 module, the HC-06 Bluetooth module, the control of the mobile phone, the control of the PWM to control the LED lamp)