搜索资源列表
uart16550
- uart16550 is a 16550 compatible (mostly) UART core. The bus interface is WISHBONE SoC bus Rev. B. Features all the standard options of the 16550 UART: FIFO based operation, interrupt requests and other. The datasheet can b
hal_omapuart
- 实现了omapl137的UART串口通信，端口，波特率，字符长度可根据用户配置，功能十分强大-Realized the UART omapl137 serial communication, port, baud rate, characters in length can be based on user configuration, the function is strong
UART
- arm下实现的串行口通信程序，功能完好，可以用ads编写-arm under the serial port communication program, function well, can be used to prepare ads
uart
- 这是一个基于vc串口异步通信 可以实现串口半双工的异步通信 -This is a serial asynchronous communication based on vc can achieve half-duplex asynchronous serial communications
UART
- 内含有完整的UART代码，包括发送和接受，且有testbench，可以直接仿真调试-Contain complete UART code, including send and receive and there testbench, can directly Simulation debugging
Uart-Carrier
- 瑞斯康公司载波模块串口通信程序,很标准的串口通信程序,可以作为学习参考.-Company瑞斯康carrier module serial communication program, it is the standard serial communication procedures, can serve as a learning reference.
uart
- uart方面的一点代码，大家可以参考一下，仅做参考-UART code that regard, we can refer to only a reference
uart
- 通用穿行通信控制器，可以直接使用，在quartsII下开发-GM through communications controller, can be directly used in developing quartsII
UART
- 使用方法： uart编程,拷贝到硬盘，用ISE打开工程文件即可-Usage: uart programming, copied to the hard drive, open the project file with ISE can
uart_fpga
- 一个完全好用的程序,用ISE 8.2打开就可直接应用-A fully-to-use procedures, with ISE 8.2 can be applied directly to open
pro104_uart
- uart的代码，经实际运行可以通信，是xilinx uart 代码的改进，网上的xilinx uart代码有很多bug，用此代码可以改进运行。-UART code, the actual operation can be communication, xilinx uart code are improved, xilinx uart code online has a lot of bug, the code can be improved with this operation.
uart
- 这是一个VC下 开发的串口通讯类，可独立进行串口操作-This is developed under a VC type of serial communication, serial port can operate independently
UART
- 本代码可以实现上位机与与单片机相互通信.如通过上位机发送启动命令后，终端会将数据传到PC上来。-you can make communicate with single ship using this code.
UART
- Verilog实现的UART程序，用ISE打开工程文件即可-Verilog implementation UART program, open the project file with the ISE can be
stm8_tda7719_6606_ZHANGWEI_GPS_MCU
- 掌微无机心 MCU 主控制程序。STM8+DT7719+6606+CAN+UART+LIN-Palm heart inorganic micro MCU master control program. STM8+ DT7719+6606+ CAN+ UART+ LIN
10.UART--LCD
- cc2430有两个穿行通信接口USART0和USART1，此源代码可以实现ZigBee节点与ＰＣ串口的通信，用于测试串口功能-cc2430 There are two walk through communication interface USART0 and USART1, the source code can be achieved ZigBee nodes and PC serial port communication, serial port functions for testi
uart
- 430 串口通信程序 能真确运行 经调试无误 能在430开发板运行-430 serial communication program can actually run through debug and correct development board to run in 430
Uart
- 51串口收发代码，原工程经测试可正常使用。-51 serial transceivers code. The test can be used normally.
UART
- ARM7 LPC2132 串口调试例程 基于Board LPC21238实验板-// UART Sample Code // NXP Semiconductors // // MCB2130 Board LPC21238: runs in internal Flash // MCB2130 Ram: runs in internal RAM //////////////////////////////////////////////////////////
usb-to-uart
- USB转UART软件，可以将USB转为UART串口通信-USB to UART software, can connect the USB to UART serial communication