搜索资源列表
disver2
- 用于镍氢电池容量测试，显示采用数码管，显示当前电压电流电量。
switchpower_mage48.rar
- 应用mage48IC编写的充电器程序功能如下： 1.充电指示 2.电量显示 3.电池保护 4.自动断电 5.充电电压选择12V24V 本程序无任何问题已经量产 ,Application procedures mage48IC function charger prepared as follows: 1. Recharging instructions 2. Electricity display 3. Battery Protection 4. Auto power off 5.
wince6.0_Battery
- wince下的电池电量显示软件,广泛用于采用wince操作系统设计的掌上型电脑- battery display software used in PDA which is designed using wince operating system
LM339
- 电池电量显示,可以使用在各种电压的电池. ....1.7V 3V 4.5V 6V 9V 12V -hd dheeed deaikkw ehbev
LDC_YB
- 基本NEC单片机的电动车液晶仪表源程序，电池电量显示，速度显示，温度显示，时间显示，里程数显示-LCD-YB
BID_NA
- 蓄电池电量监测，能够在线检测电池电量，使用10段光柱分别显示，在电量快耗完时第9段亮并输出报警-Battery power monitoring, battery power to line detection, the use of 10 bar, respectively, show that rapid consumption of electricity when finished in paragraph 9 of the output light and alarm
Battery
- 用EVC开发的WINCE下的电池电量显示软件-Developed with the EVC battery under WINCE display software
kaiguan
- 实时时钟LCD显示，并带有温度、电池电量检测等等。-The real-time clock LCD display with temperature, battery detection.
enviroment-test
- 源代友, 可以显示日期时间,温度湿度,光照强度, 以及电池电量, 功能挺全的.-Friends of source code, you can display the date and time, temperature, humidity, light intensity, and the battery, the function is very full.
LiDischarge003
- 用Atmega8单片机AD转换器电池放电器原代码，ICC AVR环境开发，C语言。单片机4个IO接指示灯，显示电池电量，1个IO控制MOSFET管开始放电或结束放电，2个IO做为按键输入。-Atmega8 microcontroller AD converter battery discharger original code, ICC AVR environmental development, C language. Microcontroller 4 IO access indicator
6wThe-solar-system1
- stc15f系列单片机，1 按键按一下，数码管显示电池电压，同时第一个led灯亮，再按一下，数码管显示电池电量，并且第二个led灯亮，经过十秒钟后数码管不显示 2 第三个led灯表示电压正常，负载可以输出，同时运用串口进行调试。-Stc15f Series MCU, the 1 key press, digital tube display the battery voltage, while the first LED lights, and then click, digital tub
ds2762
- 本系统是基于8051的锂电池电量测量系统，测量芯片是DS2762，单片机的P1.4口连接DS2762的DQ管脚，测量到的数据显示到LCD屏幕上-The system is based on the 8051 lithium battery measurement system, measuring chip DS2762, DS2762 microcontroller P1.4 port to connect the DQ pin, the measured data displayed on
676-AD
- 一款使用AD转换的电池电量管理芯片程序，主要设置电池在充电跟不充电的时候的电量显示要同步，请大家参考下。-AD converter using a battery power management chip program, the main set with not charging the battery charging when the battery indicator to be synchronized, please refer to the following.
PWR_MGT_STM8S
- stm8s开发的7.4v锂电池管理程序，具备恒流恒压充电功能，且有电量显示功能。-stm8s developed 7.4v lithium battery management program, with constant current charging function, and there is power display.
MPU6050
- 用STM32+MPU6050做的角度显示仪，能够检测绝对角度，电池电量，可以检测2个工作面-With the STM32+ MPU6050 to do the angle display, to detect the absolute angle, battery power, you can detect two faces
mpu6050_1018
- 用STM32+MPU6050做的角度显示仪，能够检测绝对角度，电池电量，可以检测2个工作面-With the STM32+ MPU6050 to do the angle display, to detect the absolute angle, battery power, you can detect two faces
ds2438chengxu
- 电池电量监测，显示剩余电池电量，监测电池的温度(Used for monitoring battery power, showing the remaining battery power)
流量计
- 以MSP430单片机为主控芯片，由TM1727液晶驱动芯片驱动段式LCD液晶显示屏，在段式LCD液晶显示屏上显示累计流量、温度、压力、瞬时流量、电池电量、流量计工作符号、天线信号强度，通过串口向差压采集电路读取温度值、瞬时流量，采用Modbus通信协议由无线通信模块将数据上传。(With MSP430 chip by TM1727 LCD driver chip driver LCD LCD display, display the cumulative flow, temperature, p
Power bank
- 单节电池两路输出(5V/2A)行动电源。 精简零组件 4段LED电量显示、以GPIO直推高亮度手电筒功能，不须外加三极管。 完整保护、高转换效率充/放电电池端之过压保护、过流保护和过温保护，并可减少功率损耗，放电转换效率最高93%。(A single - cell battery two - way output (5V/2A) power supply. Simplification of zero components The 4 section of LED power
MCU电量显示
- 单片机通过ad检测。显示当前电池电量。可以直接使用。(Single chip microcomputer through ad detection. Display battery power)