搜索资源列表
gps_f023_1103
- C8051F023的应用，主要功能是通过串口1读取GPS接收机信号，在有INT0的响应时，通过串口2发送。-C8051F023 applications, the main function is to read through a serial GPS receiver signal, INT0 in response, sent through the serial port 2.
IR_Rx_Tx
- 本程序运行于C8051F330，功能为接收遥控器发出的红外信号，然后等待上位机通过I2C总线来读取。IR数据接收完毕后，不再采集新的IR数据，一直等待上位机将数据取走后才开始准备接收新的IR数据-this program running on the C8051F330, functional remote control device to receive the infrared signal, Then wait for the PC through the I2C bus to read
pi06_src
- at91rm9200双端口RAM驱动及测试程序，支持信号量抢占，支持连续读取及重定位。-at91rm9200 dual-port RAM drive and testing procedures, the volume seize signal support, support for reading and re-positioning.
PHTO
- 利用光敏二极管作为传感器，AT89S52读取采样信号，在2位LED上面显示被测药剂浓度-using photodiode as a sensor, signal sampling AT89S52 read, In two LED above shows the measured concentration of Pharmacy
cs5550
- 常用双通道24位A/D芯片cs5550串口输出信号单片机读取程序-common dual-channel 24-bit A / D chip cs5550 serial output signal SCM reader
singalsample
- 使用AD转换芯片将模拟信号转换成为数字信号，使用DSP对转换后的数字信号读取并保存-use AD converter chip analog signal conversion into digital signals, DSP used after the conversion to digital signals and keep reading
myDoc1
- 本设 计 将 转换结束状态线STS与单片机的P1.7 相连，启动转换信号CE由单 片机的丽和丽相与所得，采用查询方式来读取AD574A的转换结果，由AO来 控制读取高8位和低4位。-the design will change end of the state line STS and SCM P1.7 connected, CE start converting signals from the MCU Laguna and Laguna phase proceeds, using i
epp_sram
- verilog语言编写的FPGA代码。功能为pc机通过epp不断写数到sram中，然后pc发送中断信号打断写过程读取sram中的数据。rar包中包含epp协议，模块文件和测试文件（test）。
sd_audio_aic23
- SD卡和AIC23数字音频输出实验, FreeDev Audio Dsp Board采用了TI公司的TVL320AIC23 1、控制接口使用I2C，Quartus中将CS置低（器件地址0011010）。 2、数字音频接口使用了组件FreeDev_aic23,有三种测试和应用 模式，中断结合DMA方式能在NIOS II中采集和发送数据。中断信号 产生于模块中FIFO缓冲区的半满信号，读取数据端口自动清除中断 请求信号。 3、I2C IP 和FreeDev_aic23 IP分别在Qu
WG34L
- 通过５１单片机的Ｉ／Ｏ口模拟ＷＧ３４信号，并读取以ＷＧ３４协议通讯的ＩＤ卡
ad
- DSP28335AD数据采集程序，读取模量信号，进行数字化
74HC165_Key
- 通过74HC166采集按键信号，读取按键值的程序。
testio
- 开关量控制模块。读取I/O口，输出开关量信号-switch control module. Read I / O port, the output switch signal
L3G4200_IIC 通过IIC总线读取L3G4200的信号的程序
- 使用ATMega16开发的，通过IIC总线读取L3G4200的信号的程序，并通过LCD1602显示。-Use the ATMega16 development, through the IIC bus read L3G4200 signal program, and through the LCD1602 display.
基于51单片机开发的通过IIC总线的ADXL345信号读取程序
- 基于51单片机开发的通过IIC总线的ADXL345信号读取程序，通过LCD1602显示。-Based on 51 SCM development by IIC bus ADXL345 signal reading program, through the LCD1602 display.
_sc_dx
- 读取信号频率，应该比较好使，谢谢大家下在，-biancheng
ZRD_TouchScreen-BlackBerry_6_090813
- 破解黑莓手机触摸屏控制的信号，从中读取信号，易于自己使用-BlackBerry touch screen control break signal from the signal read, easy-to-own use
key_signal
- 通过信号异步通知应用读取按键，解决主动读取。(Through the signal asynchronous notification application read button, solve the initiative to read.)
STM32F103控制AD7606采集模拟信号SPI
- 单片机通过SPI串行通讯，读取现场模拟量，并进行相应转换(The single chip computer reads the field simulation by SPI serial communication and makes the corresponding conversion.)
ADC_AutoCompare_demo
- 可以读取电路的AD值，将电压信号转换成数字信号(The AD value of the circuit can be read to convert the voltage signal to a digital signal)