搜索资源列表
try_sja1000
- 用51单片机控制SJA1000通信的一个小程序，其中包括对SJA1000的初始化，发送状态控制，接受程序等。-SJA1000 microcontroller control of a small communications procedures, the SJA1000 including the initialization, this state control, acceptance procedures.
51+SJA1000
- 用89C51来控制SJA1000的源码程序，C语言编写
can_selftest.rar
- 51+SJA1000+PA82C250构成的CAN节点，这是一个自收发的程序，程序是在硬件上运行通过的，没有问题的，里面有详细的注释，方便理解。可以为学习的提过一个参考。,51+ SJA1000+ PA82C250 posed CAN node, This is a self-transceiver procedures, procedures are adopted in the hardware to run on, and there is no problem, and there ar
51MCUSJA1000
- 基于51系列单片机的can总线驱动器 sja1000的驱动程序 本程序基于c8051f系列同样有用-Based on 51 Series MCU can bus drivers drive sja1000 This procedure would also be useful based on the c8051f Series
can-232
- 51单片机实现CAN总线和RS232协议之间的转换，内含SJA1000驱动程序，keil下编译通过。-51 MCU CAN bus and RS232 protocol conversion between, containing SJA1000 driver, keil compile.
SJA1000
- sja的使用可以参考一下。。。。有一定的参考价值-SJA1000 reset initialization mode only for that. Including working methods to initialize the settings, the way to receive filter settings, receive Mask Register (AMR) and receive code register (ACR) settings, baud rate and in
CAN_BUS
- ZLG 的SJA1000和CT1050合在一起的程序，发送接收都有。自己写的。已经调试通过。硬件用51+SJA1000，搞成外部RAM的INTEL模式即可。-ZLG the SJA1000 and procedures together CT1050, send to receive both. Wrote it myself. Have been through the debugging. Hardware with 51+ SJA1000, into the external RAM to
can-node-communication
- 该程序已经被多次使用，需要两个sja1000 + 51 + pca82c250的通讯模块（本程序是在P2.6和P2.5设置了LED灯来显示是否通讯成功），将源程序（kaobei.hex）下载到51单片机中，上电后通过按下两个模块的复位键，就能看到对应的模块有指示灯显示-The program has been used many times require two sja1000+ 51+ pca82c250 communication module (the program is set in
51-SJA1000
- 可以实现在PC与CAN总线的连接。采用的89C51和SJA1000芯片的接法.（已实现）-Can be achieved in the PC and the CAN bus connection. The 89C51 and SJA1000 chip using the access method. (Realized)
CAN_SJA1000
- 51单片机，SJA1000的CAN控制芯片，实现CAN总线自收发，速率为1M-51 SCM, SJA1000 CAN controller chip, the CAN bus from the transceiver, the rate of 1M
89C51_CAN
- 基于89C51单片机和SJA1000的CAN总线通信测试程序，调试通过，完全可以使用。-89C51 microcontroller and the SJA1000 based CAN bus communications test program debugging, can be used.
sja
- CAN通信例程，通过51、SJA1000和CAN驱动器连接can总线，接受另一can节点发来的一个字节信息并通过LED实时显示出来-CAN communication routines, through 51, SJA1000 CAN driver and connector can bus, the node can accept another byte of information sent by a real-time LED display
SJA1000-can
- SJA1000 CAN控制器与51单片机通讯代码，调试通过，能进行CAN2.0B收发，附有芯片使用手册帮助理解代码-SJA1000 CAN controller with 51 single-chip communication code, debugging through, can CAN2.0B transceiver attached to the chip manual to help understand the code
51-sja1000
- 用51单片机作为微控制器，sja1000作为can控制器，实现can的自发自收。-51 microcontroller as microcontrollers, sja1000 as can controller can spontaneous collected.
SJA1000-based-CAN-bus-communication
- 基于51单片机和CAN总线控制器SJA1000，CAN总线通信例程-Based on 51 single and CAN bus controller SJA1000, CAN bus communication routines
GROUPFinal
- 本人所写。使用CAN2.0B标准发送大于8B的报文，保证一个节点可以一次传送完报文而不被打断。使用51+SJA1000完成，如何使用SJA1000也很有参考价值-I write. Use CAN2.0B standard to send more than 8B of the message, to ensure that a node can send a message without being interrupted. Using 51+SJA1000 to complete, how
IAR-C51-SJA1000
- IAR 编译器下 用51单片机 驱动CAN芯片 SJA1000 程序代码。 -IAR compiler with 51 single-chip driver SJA1000 chip CAN program code.
SJA1000-CAN-
- KEIL 编译器下 51单片机驱动CAN总线芯片 SJA1000 实现 CAN 总线通讯-KEIL compiler under the 51 single-chip driver CAN bus chip CAN to achieve SJA1000 bus communication
sja1000程序
- sja1000 配置c程序。。。。。。。。。。。。。。。。(sja1000 Configuring the C program)
基于SJA1000的51单片机CAN通讯源代码
- 附件为基于SJA1000的51单片机CAN通讯源代码，稍微修改就可以应用到其他类型的单片机系统中