搜索资源列表
Huffman.c2
- 1．在发送端通过一个编码系统对待传数据预先编码，在接收端将传来的数据进行译码（复原）。对于双工信道（即可以双向传输信息的通道），每端都需要一个完整的编/译 码系统。 2．本程序的目的是大大提高通信的信道利用率，缩短信息传输时间，降低传输成本。 -1. In the transmitter through a coding system for pre-treatment data-coding the receiving end of data from the decodin
mt
- MT: windows NT/2000/XP command line tape manipulation written to format a tape windows-XP backup refused to write or format... and satisfy my curiosity Can be used for crude data recovery (combine seek and read)
5B6B
- FPGA的5B6B编译码器的设计代码可以编译而且有波形图 -5B6B code is used in fiber optic digital communication systems a more extensive line pattern! Data are 5B6B encoding and conversion, and string after the fiber transmission, serial code sequences in continuous bit 0 or b
HDB3encoder
- 数字基带信号的传输是数字通信系统的重要组成部分。在数字通信中，有些场合可不经过载波调制和解调过程，而对基带信号进行直接传输。采用AMI码的信号交替反转，有可能出现四连零现象，这不利于接收端的定时信号提取。而HDB3码因其无直流成份、低频成份少和连0个数最多不超过三个等特点，而对定时信号的恢复十分有利，并已成为CCITT协会推荐使用的基带传输码型之一。为此，本文利用VHDL语言对数据传输系统中的HDB3编码器进行了设计。-Digital baseband signal transmission i
shift
- E1接收部分主要功能是实现从输入的差分线路数据中恢复出2.048M线路时钟并将数据解码输出。包括解码和线路时钟恢复两模块。-E1 to receive some of the major functions of the difference from the input data lines to recover a clock and data lines 2.048M decoder output. Including decoding and clock recovery circuit
hdb
- 数字基带信号的传输是数字通信系统的重要组成部分。在数字通信中，有些场合可不经过载波调制和解调过程，而对基带信号进行直接传输。采用AMI码的信号交替反转，有可能出现四连零现象，这不利于接收端的定时信号提取。而HDB3码因其无直流成份、低频成份少和连0个数最多不超过三个等特点，而对定时信号的恢复十分有利，并已成为CCITT协会推荐使用的基带传输码型之一。为此，本文利用VHDL语言对数据传输系统中的HDB3编码器进行了设计。 基于达到达到达到的信号发生器的源程序-Digital baseband
SEEDVPM642_led
- DM642开发板的LED实验代码，内含BOOT程序，DSP上电自启动过程中，自动恢复RAM内应用数据-TI Series dsp Shaoxie during the BOOT process necessary to ensure the DSP power-on self-starting process, the application of automatic recovery of data RAM
5b6b
- 5B6B码是光纤数字通信系统中使用比较广泛的一种线路码型! 数据经过5B6B编码和并串转换后在光纤上传输，串行码序列中连续的比特0或比特1的长度不超过5，数据在0和1之间变换的密度很高,并具有直流平衡的特性，有利于接收电路和时钟恢复电路的设计。-5B6B code is used in fiber optic digital communication systems a more extensive line pattern! Data are 5B6B encoding and conver
DigiTecProDataRecoverEn
- Data recovery tool for Digitech Pro device - works with full memory dump
SERDES
- 基于Verilog的串并转换器的设计与实现，采用两种不同的方案来实现串并和并串转换的功能，并用ISE软件仿真以及chipscope的调试-Verilog-based serial and parallel converter design and implementation of two different programs to achieve the string and and and string conversion functions, and use the ISE softwa
24C08_1
- 基于P89V51单片机和24C08串行flash的程序；可以实现断电数据恢复；-Microcontroller and 24C08 based serial flash P89V51 procedures can achieve power data recovery
rfc5109.txt
- This document specifies a payload format for generic Forward Error Correction (FEC) for media data encapsulated in RTP. It is based on the exclusive-or (parity) operation. The payload format described in this document allows end systems to appl
recovery
- 恢复时钟信号的代码,用于数字通信中，used to recovery the timing from data-used to recovery the timing from data
xapp250
- xilinx 关于时钟数据恢复中的源代码-xilinx on the clock and data recovery in the source code
xapp224datarecovery
- Data recovery allows a receiver to extract embedded clock data from an incoming data stream. The receiver usually extracts the data from the incoming clock/data stream and then moves this data into a separate clock domain. Sometimes, the receiver
STM32-Touch-screen
- 开机的时候先通过24C02的数据判断触摸屏是否已经校准过，如果没有校准，则执行校准程序，校准过后再进入手写程序。如果已经校准了，就直接进入手写程序，此时可以通过按动屏幕来实现手写输入。屏幕上会有一个清空的操作区域（RST），点击这个地方就会将输入全部清除，恢复白板状态。程序会设置一个强制校准，就是通过按KEY0来实现，只要按下KEY0就会进入强制校准程序，这个强制校准程序是必须的-Boot time to pass the the 24C02 data to determine the touc
GPS_WIRELESS_RXD
- 通过无线模块接收GPS压缩数据，并进行校验和错误恢复，恢复算法采用位判别，三中取二。-GPS compressed data received through the wireless module and the checksum error recovery, the recovery algorithm uses a bit discriminant of three samples.
cdr
- 数据时钟恢复，采样8倍率高频时钟进行数据时钟恢复。已通过Modelsim仿真-Data and clock recovery, sampling 8 times the rate of high frequency clock for clock and data recovery. Have been through the Modelsim simulation
iap心得
- 单片机引导程序资料，对新程序的引导写入以及写入失败旧程序恢复(Single chip boot program data, the new program boot write and write failed, the old program recovery)