搜索资源列表
IO输出-点亮1个LED灯方法
- 点亮P1口的一个LED灯 该程序是单片机学习中最简单最基础的， 通过程序了解如何控制端口的高低电平
4位7段led灯控制
- 4位7段led灯的控制，0000-9999动态显示
DIPcontrolLED 基于DSP的拨码开关控制LED灯的亮灭
- 基于DSP的拨码开关控制LED灯的亮灭，是在TMSVC5509A上在CCS开发工具中编写的。-dsp led dip ccs tmsvc 5509
led-qt.rar
- 这个是sbc2410开发板上的通过qt，在触摸屏上控制开发板上的led灯的亮灭。具体操作有一个说明！可以互相交流一下。,This is a development board sbc2410 through qt, in the development of touch-screen control panel of the bright lights led out. There is a specific operation that!
led
- AVR单片机ATMEGA48控制LED灯的C程序-AVR Single Chip LED lights ATMEGA48 control C program
tc35-mcu-led
- 实现短信控制单片机板上的LED灯 控制电平，可拓展为控制继电器 -Message board microcontroller to achieve the control level LED light control can be expanded to control relay
LED
- 用VHDL语言实现的八个开关控制八个LED灯的亮灭，本程序经过实验箱认证，绝对可用。-VHDL language used to achieve the eight switch control eight bright LED lights out, the procedure experimental boxes after certification, available absolutely.
XLLEDKZ
- 标题: xl系列单片机实验仪演示程序PWM 控制 LED 灯渐亮渐灭程序 * * 文件: xlledkz.asm * * 日期: 2006-1-5 *-Title: xl series Singlechip Tester demo PWM control bright LED lights gradually become out procedures** file: xlledkz.asm** Date: 2006-1-5*
LED
- 用pic12c509实现的闪灯控制，主要应用于广告灯和酒吧彩灯方面-Pic12c509 realize with the blinking light control, mainly used in ads lantern lights and a bar area
led
- 用一个按钮开关循环控制四个led灯的闪烁方式，输入时钟10MHz，闪烁频率1Hz-Button switch with a four cycle control lights flashing led the way, the input clock 10MHz, blinking frequency of 1Hz
led
- 基于51的智能流水灯控制，一个经典的算法，本人已经经过验证，仅供大家参考-51 water-based intelligent light control, a classical algorithm, I have been verified, for your reference
PWM-LED
- 基于51单片机控制的pwm输出，，占空比可调节，负载位led灯，根据led的亮度强弱可判断pwm占空比的大小-Based on 51 MCU-controlled pwm output, duty cycle can be adjusted, the load position led lights, under the led brightness pwm duty cycle can be judged the strength of the size of the
脑电语音控制LED灯
- 本程序通过使用脑电和语音通过串口通信与32连接控制led灯(This procedure through the use of EEG and voice through serial communication and 32 connection control LED lights)
1、（通用IO口方式）实现LED灯全亮全灭闪烁
- 通用I/o口控制 led流水灯闪烁 全亮全灭(General I/o port control LED water lamp flashing full bright full kill)
STM8S103F3GPIO输出_流水灯控制___Lib
- STM8S103F3GPIO输出_流水灯控制LED(The output of the STM8S103F3GPIO _ light water control ___Lib)
4.短信控制led灯
- 能使用该程序运用单片机和SIM900A模块控制LED灯的亮灭(The program can be used to control the brightness of the LED lamp by using the single chip computer and SIM900A module)
11.按键无线控制台灯和LED灯 继电器
- 在zigbee协议栈中 按键无线控制台灯和LED灯 继电器(Key wireless control desk lamp and LED lamp relay in ZigBee stack)
LED灯外部中断
- 用单片机的外部中断来控制LED灯的亮灭（库函数开发）(External interrupts with the microcontroller to control the LED lights off (library function development))
8个按键控制8个LED灯
- 实现按键控制led灯，包括线路连接方法，很实用普中单片机开发板。(Achieve button control LED lights, including line connection method, very practical microcontroller development board.)
交通灯控制
- 包含proteus仿真文件及c语言程序，在开发板上进行过运行。利用双色LED显示电路，和四位静态数码管显示电路模拟十字路口交通信号灯。4位LED数码管显示时间，双色LED灯显示红绿灯状态。熟悉交通信号灯控制逻辑。设计一个十字路口的交通灯控制电路，要求南北方向和东西方向两个交叉路口的车辆交替运行。每次绿灯变红灯时,要求黄灯先亮3S,才能变换运行车辆。东西方向、南北方向车道除了有红、黄、绿灯指示外，每一种灯亮的时间都用数码管显示器进行显示（采用倒计时的方法）。考虑到特殊车辆情况，设置紧急转换开头。(