搜索资源列表
PWM_for_C51
- 使用定时器产生PWM波，可配合L298N用来驱动普通直流电机。适用于51单片机-use PWM timer generated wave, and with the drive for general L298N Motor. Apply to the 51 SCM
PWM.zip
- 单片机产生PWM信号控制直流电机调速,T0产生双路PWM信号，推动L293D或L298N为直流电机调速,Single-chip generated signal PWM DC motor speed control, T0 dual PWM signal generated to promote the L293D or L298N to DC Motor Speed Control
PWM
- 51单片机驱动L298N，驱动直流电机，程序经过测试。-51 Microprocessor L298N, drive DC motor, the program tested.
motor
- 利用89C51的定时器产生PWM控制直流电机的转速及方向-89C51 generated using the timer PWM DC motor speed control and direction of
PWM
- 单片机利用PWM信号控制直流电机调速 接L298N时相应的管脚上最好接上10K的上拉电阻。 -Microcontroller using PWM signal control DC motor speed access L298N best when the corresponding pin of the pull-up resistor connected to the 10K.
PWM_and_L298N
- pwm与L298n程序 电机最终版(极品！！！)-pwm motor program with the final version L298n (Need!!!)
PWM
- PWM 调速 L298N芯片-PWM
pwmqianjinhoutui
- AT89S52 L298N PWM调速 超过设定速度反转 循环过程-PWM speed exceeds a set speed reverse cycle
PWM-L298N
- 使用8051单片机和l298n对电机实现调速-failed to translate
main.rar
- 51单片机通过PWM控制直流电机的驱动，L298N 驱动芯片，可以通过串口，用上位机来控制，控制直流电机的正反转，加速减速,PWM control DC motor driver L298N 51MCU through the serial port, using the host computer to control, control of a DC motor reversing, acceleration and deceleration
AVR_Motoer_PWM
- AVR 使用PWM驱动L298N程序.使用了相位修正PWM。2K的频率。效果比较好
motor
- AVR使用硬件PWM驱动L298N来控制电机，PWM频率为2K-AVR hardware PWM driver L298N to control the motor, PWM frequency for 2K
L298N
- 基于单片机的PWM直流调速，LCD1602显示，占空比可变-Microcontroller-based PWM DC converter, LCD1602 display, variable duty cycle
PWM
- 51单片机利用L298N芯片驱动直流电机，通过按键PWM调速。-51 use L298N chip microcontroller drive DC motor PWM speed control via buttons.
L298N-DCMOTOR-PWM
- L298N PWM调速 直流电机 C51-PWM L298N speed control DC motor C51
pwm
- 通过该IP核输出三路pwm波，可用来控制一个舵机和两块L298N驱动板，从而控制电机。-IP core output by the three-way pwm wave can be used to control a servo drive plate and two L298N to control the motor.
PWM电机 - 副本
- 驱动直流电机，通过l298n来驱动，stm32板拉高引脚PA9与PA10，同时PA7输出PWM值(The drive DC motor is driven by L298N, the STM32 board pulls the high pin PA9 and the PA10, and the PA7 outputs the PWM value)
1.PWM调速电机控制(6.10)
- 简单的PWM利用L298n驱动器控制双电机。(The PWM uses the L298n drive to control the motor.)
stm32f10x_temple-nb-1401011140
- stm32开发板上通过配置tim2的通道1通道2和tim3的4个通道，产生六路pwm输出波，与l298n模块相连接，控制并实现三个减速电机的变速(STM32 development board, through configuring TIM2 channels, 1 channels, 2 and tim3 4 channels, generates six PWM output waves, and is connected with L298N module, controlling an
PWM+蓝牙+小车
- STM32F103ZET6用（PWM）+HC05（蓝牙）+L298N（驱动）制作的蓝牙控制小车)(STM32F103ZET6 Bluetooth control car made by (PWM) +HC05 (Bluetooth) +L298N (driver))