搜索资源列表
drv
- H9200F的RTC驱动 1、将驱动程序rsound.o拷贝到系统目录：/lib/modules 2、执行如下命令加载模块： insmod /lib/modules/at91_rtcex.ko
8b_10b
- vhdl编写，8b—10b 编解码器设计 Encoder: 8b/10b Encoder (file: 8b10b_enc.vhd) Synchronous clocked inputs (latched on each clock rising edge) 8-bit parallel unencoded data input KI input selects data or control encoding Asynchronous act
spca5xx.ko.tar.gz
- spca5xx.ko为中星微电子301摄像头驱动，在使用时用insmod spca5xx.ko命令插入该模块，运行 udevstart命令后，再运行./v4lcap 便可显示 ,Vimicro spca5xx.ko for 301 camera-driven, when in use insmod spca5xx.ko order to insert the module, run udevstart command, and then run ./v4lcap will be able
Chapter_6_Advanced_experiments_part1
- 周立功magic2410实验箱源码 第6章Linux高级实验(part1) 6.1 Linux内核编译实验 6.2 Linux根文件系统实验 6.3 CAT1025读/写实验. 6.4 ZLG7290键盘读取 6.5 USB-E2PROM编程器实验 6.6 SD/MMC卡实验 6.7触摸屏实验 6.8 PCMCIA接口CF卡实验 -Magic2410 week experimental box Ligong source Linux High Chapte
18B20
- 18B20.c为驱动模块-->18B20.ko 18B20test.c为测试应用程序-->18B20test.o -18B20.c for the drive module-> 18B20.ko 18B20test.c to test the application-> 18B20test.o
mini2440_buttons
- 嵌入式LINUX按键测试程序及其相应的测试代码-Embedded LINUX key test procedures and their corresponding test code
adc
- arm 2440 开发板下ADC转换驱动 内包括驱动源文件，KO文件，驱动测试源文件-arm 2440 develop demo ADC driver content driver source code .kofile driver test code
gtksrc_101108_01.tar
- 这是我自己写的gtk的练习程序，想学gtk的可以参考一下 这里建立的是两个window，但是在第二发window关闭后，如何返回设置第一个window为当前界面？ 101103，打开一个驱动测试 自己做的GIOSetdev.ko 成功使用；-This is my own exercise program to write gtk, gtk-can refer to learn click here for building a two window, but made in
newdriver
- 华为U6100在linux的驱动，编译后加载进内核然后拨号即可-driver in linux of Huawei U6100, compile the source file and then load the .ko file into the kernel ,after these we can dial and access web!
Xsy-Light-KO
- 单片机用十字路口灯控制，绿灯40s，后3s闪亮，红灯30s，可修改-MCU control with intersection lights, green 40s, 3s after the shiny, red 30s, can be modified
Ex1TM01
- 8 位 nec 单片机 KO kE系列间隔定时器源程序-8bit nec mcu ko ke timer source
Ex1TM51
- 8位 nec 单片机KO KE1系列tm5定时器源程序-8bit nec mcu ko ke1 series tm5 timer source
mini2440_gpio
- 本人自己开发的基于mini2440的GPIO驱动，包括源码和已经编译好的linux-2.6.32.2的KO文件，直接可以使用，驱动的引脚可以通过源码查到。-mini2440 gpio driver for linux-2.6.32.2
eeprom
- 在arm-linux2.6.28版本上的基于I2C的EEPROM的模块（eeprom.ko)。-Version of the arm-linux2.6.28 EEPROM on the I2C-based module (eeprom.ko).
PID
- PID tuning Use simulink response optimalization to tune the gains Kp Ko Kd of the PID controler block PID tunning with actuator constraints-PID tuning Use simulink response optimalization to tune the gains Kp Ko Kd of the PID controler block PID tun
FLA414SH
- 本例程演示了如何编程FLASH。 程序运行后，如果编程正确，液晶屏会显示： STM32F10x DEMO FLASH TEST: OK 如果编程错误，液晶屏会显示： STM32F10x DEMO FLASH TEST: KO -This routine demonstrates how to program FLASH. After the program is run, if the programming is correct, the LCD will disp
outio
- MINI2440开发板电机CON4 GPIO引脚驱动程序,四个引脚分别为9、10、11、12。 c程序加编译好的ko驱动模块-MINI2440 CON4 GPIO pin development board motor driver, four pins 9,10,11,12 respectively. c program plus driver module compiled ko
sun8iw5p1.tar
- 此代码为全志R16(A33)平台，nand驱动的代码，R16源码在init.rc阶段支持nand模块加载，但需要把生成的nand.ko放入ramdisk.img中，并且能调用insmod命令插入nand模块，这样才可正常启动。-this nand driver code is based on R16 soc of allwinner. if you develop board want to support nand flash ,you can put nand.ko in RAMDISK.
Lecture_7
- is ko lu ir hte gtb its pure notes
DHT22-master
- KO CO GI DAU DUNG DOC