搜索资源列表
gmt203
- 完整功放的控制程序，里面包括VFD，控制面板，音量控制，音效控制，红外遥控等功能-complete PA control procedures, including inside VFD, control panels, volume control, audio control, infrared remote control functions
8255 输入
- 8255 输入、输出实验的汇编程序清单 方式0，PA，PC输出，PB 输入-Source code in assembly of using 8255 to input and output. 8255 is set as mode 0, i.e., PA and PC are used as output ports, PB is used as input port.
功放前级程序
- 利用单片机对功放前级进行控制。并且有遥控功能，-SCM former right-PA control. And a remote-control function,
ATs513
- AT90S8515的PA口LED广告灯演示程序-AT90S8515 PA mouth advertising LED lights Demonstration Program
clkk
- === =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06
mul4
- --- -initial--- - MOVLA 00H IODIR PA IODIR PB IODIR PC MOVAM PA MOVAM BSR MOVAM STATUS MOVAM TMR0 MOVAM TMR1 MOVAM TMR2 -------end initial----- -------------乘法运算------------ 乘数->10H 被乘数->11h 结果(积)-
ram96
- --- -initial--- - MOVLA 00H IODIR PA IODIR PB IODIR PC MOVAM PA MOVAM BSR MOVAM STATUS MOVAM TMR0 MOVAM TMR1 MOVAM TMR2 ----------------------- MOVLA AAH 写入RAM的数据 MOVAM 08H MOVAM 09H MOVAM 0AH MOVAM 0
Seg2
- Dsp2407 七段显示器 动作：四位数扫描计数器，以十进制显示0000~9999 以快速或动态执行观察PA及PB脚输出的变化 -Dsp2407 paragraph 107 monitors movements : the four-digit scanning counter, in the metric system showed 0,000 ~ 9,999 to rapid or dynamic observation PA and PB output pin changes
key_W29C020_music+code
- 这是我用汇编语言写的音乐播放程序 此程序为用89c51控制 输出为 lm386 功放 本程序中有14首曲子代码 均是本人花费大量时间手工转换 本程序之所以叫key_W29C020_music+code 是因为本程序是写在W29C020芯片中的 单片机中不用写程序 W29C020是主板上的bios芯片 256k 的flash 当然 你也可以将代码烧到89c51中 -This the compilation of language I used to write music pla
8255_PA
- 在#MCU2的数码管上显示1，2，3，4 用定时器设置一个占空比不等的方波信号， 在8255的PA口，用LED的亮灭来表示-# MCU2 in digital pipe showed 1,2,3, 4 Set the timer with a duty cycle ranging from the square wave signal, in 8255, PA mouth, The bright LED to indicate destruction
avr-4
- AVR单片机入门及C语言高效设计实践（四） ATMEAG16L的I／O端口特点及使用 ATMEAG16L单片机有32个通用I／O口，分为PA、PB、PC和PD四组，每组都是8位。这些I／O口都可以通过各自的端口寄存器设置成输入和输出（即作为普通端口使用），有些I／O口还具有第二功能（我们在后面使用到这些第二功能时再介绍）。-AVR C language portal and efficient design practice (4) ATMEAG16L the I / O Ports cha
key_lcd
- proteus应用实例尝试过用PD口和PC口，但总是存在检测不 到按键的情况，所以改用PA口
key_lcd
- 尝试过用PD口和PC口，但总是存在检测不 到按键的情况，所以改用PA口
2.4GRFAmplify
- 2.4G PA 原理图 用于wifi 信号放大，非常难得的资料-2.4G PA schematic for the wifi signal amplifier, the data are very rare
AN_037_CC2420_w_PA_PCB
- Chipcon CC2420 reference design w/PA board rev B CC2420_w_PA_PCB.ZIP FABRICATION.PHO - fabrication drawing COPPER1.PHO - copper layer #1 (top side) COPPER2.PHO - copper layer #2 (inner ground plane) COPPER3.PHO - copper layer #3 (inner
CC1100
- A firmware driver for CC1100 based SubGHz RF modem. Target used is a PIC16F877A series. The code is written and tested for a RF modem by Summitek model ST-TR1100+PA. SPI is implemented in the software itself and can be driven in burst mode also. -A f
PA-design-using-ADS
- 对利用ADS设计PA进行了详尽的介绍，适合微波通信专业相关下载-PA on the use of ADS design a detailed introduction, suitable for microwave communications professional Download
jf24d-pa.cktxcx
- 2.4GHz模块，带PA功放，距离更远，适合对距离有要求的客户使用-2.4GHz Module with PA amplifier, farther, on the distance required for customers to use
Presentation_on_RF_Predistortion_of_Power_Amplifie
- 利用ADS设计功放（PA），提供了一些设计步骤以及理论，同时利用ADS设计RF预失真，来提高功放的线性度-Design using ADS amplifier (PA), provides some design procedure and theory, while taking advantage of ADS design RF Predistortion, to improve the linearity power amplifier
WIA-PA-Protocol-Stack
- WIA P rotocol Stack，WIA-PA协议说明，适合学习者-WIA PA Protocol Stack