搜索资源列表
aduc7000_pwm
- This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 an
st10f166_adc
- This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial p
signalgenerater
- 一个简单的多种信号的发生器 包括正玄，锯齿，阶梯等，使用时用quartus 4.0以上版本打开-a simple multiple signal generator including Shogen, sawtooth, the ladder, when used with the above version 4.0 Quartus open
cosinexp123
- 1.分别利用计算法和查表法产生1000Hz的余弦波信号，并使用示波器观测产生信号的频率和幅度。 2.利用计算法产生其他非正弦类周期信号波形，如周期矩形波、三角波、锯齿波等。-1. Each calculation method and the use of look-up table method have 1000Hz the cosine wave signal, Oscilloscope observation and the use of the generated signal f
wave_genarator_vhdl
- vhdl波形发生程序.实现4种常见波形正弦、三角、锯齿、方波（A、B）的频率、幅度可控输出（方波 A的占空比也是可控的），可以存储任意波形特征数据并能重现该波形，还可完成 各种波形的线形叠加输出。 -vhdl waveform occurred procedures. 4 achieve common sinusoidal waveform, 1.30, sawtooth, square-wave (A, B) the frequency and amplitude control
Sawtooth
- Program for 8051 in assembly language which produce Sawtooth wave by means of a simple DtoA
NO.21-sawtooth-with-DAC0832
- 《单片机C语言程序设计实训100例——基于8051+Proteus仿真》案例压缩包 第 02 篇 第 02 篇 硬件应用 21 用DAC0832生成锯齿波-" Microcontroller C Programming Language Training 100 cases- based on 8051+ Proteus simulation," Case No. 02 archive 02 hardware applications generate sawtooth
sawtooth-waveform
- 在ＦＰＧＡ中产生的频率可调的锯齿波型信号发生器-The frequency of the FPGA to generate the sawtooth waveform signal generator adjustable
PCF8591-output-sawtooth
- PCF8591 输出锯齿波同，新手可以看看！不错的源码~-PCF8591 output sawtooth wave with the novice can see! A good source ~
Generated-sawtooth
- 用51单片机控制DAC0832生成锯齿波。利用Proteus和keil软件进行系统的仿真设计。-MCU control with 51 DAC0832 generates a sawtooth waveform. The use of Proteus and keil software for system simulation design.
Sawtooth-wave
- 产生锯齿波波形代码，其产生的波形失真较小，精度很高-Sawtooth wave
dac0832-Sawtooth
- 利用at89c51和adc0832产生锯齿波，具有清零的功能，利用算法实现-At89c51 and adc0832 produce sawtooth, with a clear function, the use of algorithms to achieve
sawtooth
- 本程序是基于msp430单片机的DA锯齿波发生器-This procedure is based on the the MSP430 microcontroller DA sawtooth generator
sawtooth-generator
- 这是一个锯齿波形的发生器程序，可以提供我们需要的锯齿波形，-This is a sawtooth waveform generator program can provide we need a sawtooth waveform,
The-64-PCF8591-output-sawtooth
- The 64-PCF8591 output sawtooth单片机输出锯齿波-The 64-PCF8591 output sawtoothMicrocontroller output sawtooth
DAC0832-generated-sawtooth
- DAC0832生成锯齿波 包含KEIL文件和DSN文件-DAC0832 generated sawtooth DSN file that contains the files and KEIL
PCF8591-output-sawtooth
- 51单片机和pcf8591输出锯齿波。程序简单实用。-51 And pcf8591 output sawtooth. Procedure is simple and practical.
Sawtooth
- 在Altera DE2-70的开发板上实现产生锯齿波信号。-In the Altera DE2-70 development board realize sawtooth signal.
Use-DAC0832-sawtooth
- 通过在DAC0832的输出端接运算放大器，由运算放大器产生锯齿波实现-DAC0832 output termination by the operational amplifier, produced by the operational amplifier to achieve the sawtooth
Output-sawtooth
- 锯齿波型号发生器,使用DA输入，数码管显示输出数字量，LED显示模拟电压大小及频率。-PCF8591-Output sawtooth