搜索资源列表
7810howtocounthot
- 以7805为例说明问题。 设I=350mA，Vin=12V，则耗散功率Pd=(12V-5V)*0.35A=2.45W 按照TO-220封装的热阻θJA=54℃/W，温升是132℃，设室温25℃，那么将会达到7805的热保护点150℃，7805会断开输出 -7805 as an example to illustrate the problem. Located I = 350mA, Vin = 12V, the power dissipation Pd = (12V-5V)* 0
minidmxprog22
- vin avr dimmer for dmx 512 strob
CS5460A_forWeighing_Application
- using CS5460A for weighing scale application with LCD interface. will give the reading of VIN+ and VIN- pins to LCD. Compiled with avr-gcc that shipped with flowcode targeted to ATMega32.
c11-7
- 作原理（电路见附图） 1.上电复位，读取24C02中的电压，送DA转换输出电压，如24C02中电压为0则设置初始电压为5Vo 2.电压控制：通过键盘S1、S2，控制MCU产生8位数字信号（0-255），通过P3口送至8位数模转换芯片(DAC0832)转换成模拟电流信号，再经运放作I/U转换，得到控制稳压电源输出部分的基准电压。 3.电流取样：采用8位模数转换芯片(ADC0804）作为显示电流的模数转换器件，ADC0804的取样电压由串联在电源输出电路的电流取样电阻（0.1Ω）分压取得
lpc213xremap
- lpc213x在keil环境下VIN的编程-The LPC213x keil write the vin
A1
- IAR环境下 MSP430-149F，以参考电压为采样信号的ADC采样示例程序，当采样到的电压A0>0.5*AVcc，P3.4（LED）置位，否则复位。- MSP-FET430P140 Demo- ADC12, Sample A0, Set P3.4 if A0 > 0.5*AVcc Descr iption: A single sample is made on A0 with reference to AVcc. Software sets ADC10SC to
A2
- IAR环境下的MSP430F149,使用内部参考电压为采样信号的单路AD转换的采样程序。- MSP-FET430P140 Demo- ADC12, Using the Internal Reference Descr iption: This example shows how to use the internal reference of the ADC12. It uses the internal 2.5V reference and performs a single
STM32F105_OBDII_CAN-CODE
- STM32F105和OBDII_CAN的接口程序。具体是测试 OBDII CAN总线的协议类型和速率，并读取VIN。-STM32F105 and OBDII_CAN interface program。detail is that Test OBDII CAN s rate and get Car VIN from OBDII.
TempShunt PIC16F628A
- PIC 16F628A Dallas DS18S20 Tempregulator ext. Vin (0V=20C/5V=40C) or local DS2890 Serial out for log 7-Seg Temp display Current & Set
CS5460A_forWeighing_Application
- using CS5460A for weighing scale application with LCD interface. will give the reading of VIN+ and VIN- pins to LCD. Compiled with avr-gcc that shipped with flowcode targeted to ATMega32.
CS5460A_forWeighing_Application
- using CS5460A for weighing scale application with LCD interface. will give the reading of VIN+ and VIN- pins to LCD. Compiled with avr-gcc that shipped with flowcode targeted to ATMega32.
ADC-PWM
- 3 ADC Vin convert in 3 PWM output 15khz set (ptper for varying frequence)
P&O of MPPT
- FILE: Colltroller of Buck DC-DC Converter.c // TITLE: P&O of MPPT by disturb of Input Voltage (Vref+/-deltaV). // ASSUMPTIONS: // This program requires the DSP281x V1.00 header files. // As supplied, this project is configured for "boot to H