搜索资源列表
FLUEPROG
- 一个流量控制仪器的源码，p89c668单片机，继电器输出／LED输出／can总线／智能卡／rtc等-a flow control device of the source code, p89c668 microcontroller, Relay output / output LED / can Bus / smart card / rtc etc.
rs232
- RS232.C was written to provide all of the basic functionality needed to employ serial I/O in any application written with Borland C language compilers. Some features are: 1. Ease of use. No assembly language or library files are use
EasyARM1138UART
- 本例是easyarm1138的UART(通用异步收发器)实例 建议采用Windows自带的“超级终端”来调试UART， 在“端口设置”里，设置如下 波特率：9600 数据位：8 奇偶校验：无 停止位：1 数据流控制：无 -This case is easyarm1138 the UART (Universal Asynchronous Receiver Transmitter) proposed to u
wendupid
- PID技术，C代码文件，拷贝其中部分代码稍加修改就可以控制温度、流量、压力等。-PID technology, C code files, copy the code slightly modified some of them can control the temperature, flow, pressure and so on.
P_U
- TIC5000系列，超低功耗芯片C55的程序控制部件PU的源代码，PU负责指令流控的功能-TIC5000 series, ultra-low power chip process control component PU C55 source code, PU is responsible for command flow control functions
USART
- STM32F103VBT6开发板上的串口中断程序，通过串口控制流水灯-STM32F103VBT6 development board serial port interrupt program, through the serial port flow control lamp
TIM
- STM32F103VBT6开发板上的定时器中断程序，控制流水灯-STM32F103VBT6 development board timer interrupt program flow control lamp
S3C2410-init
- 基于ARM9芯片S3C2410异常中断程序设计。验证的代码详细分析了基于ARM嵌入式系统的异常处理流程。然后阐明关键字“-irq”的作用，设计出中断处理函数。最后，通过设置中断控制寄存器，设计外部中断EINT3的初始化程序，并给出主程序流程图。实践证明程序运行稳定可靠。-S3C2410 ARM9-based chip exception interrupt programming. Detailed analysis of the code verification of embedded sy
GPIO_Leds8
- 飞利浦ARM7之LPC2132的8路流水灯控制应用程序，含ADS1.2的编译工程文件，你也可以自己将文件里的主函数mai.c复制到你自己的编译环境里均可以。让你轻松学习ARM7的GPIO的操作及使用。-Philips LPC2132 ARM7 8-way flow of light control applications, including ADS1.2 compiled project file, you can own the file in the main function mai.
RTC-set-the-clock-and-display
- RTC时钟源为外部低速时钟，且外部低速时钟源的64分之一Tamper引脚（PC.13)上输出。 通过秒中断功能，在LED1(GPIO_Pin_0)上以2s为周期闪烁，并以1s为周期通过USART送出时间信息 （在串口调试软件上以24小时时间制显示） USART1设置：波特率：9600 数据位：8 停止位：1 奇偶校验位：无 硬件流控制：无 注：编译时，Library Configuration应选为FULL，以使C库函数fputc映射到U
STM32F103uart
- STM32F103的串口通讯例程 This example provides a descr iption of how to use the USART with hardware flow control and communicate with the Hyperterminal. First, the USART2 sends the TxBuffer to the hyperterminal and still waiting for a string from the
PC-send-ab-control-P1-led-flow-order
- 基于IAR Embedded Workbench IDE开发环境的MSP430 单片机接受处理pc发送的数据点亮LED的小程序-Based on MSP430 MCU IAR Embedded Workbench IDE development environment to accept data processing pc LED lights sent a small program
px4flow-klt-06Dec2014
- px4flow光流传感器固件，可以直接利用pixhawk飞控实现室内自主飞行。-Px4flow optical flow sensor firmware, pixhawk can be directly used to achieve autonomous flight flight control room.
vj758
- Achieve a grayscale image and further control for video surveillance, matlab prepared cellular automata, Multi-machine power system simulation and flow calculation.
2.流水灯
- atmega128使用的程序，流水灯控制程序。通过IO口控制流水灯，亮和灭(The program used, the flow light control program. Control flow light through IO port, light and extinguish)