搜索资源列表
6.GPIO输出实验-LED数码管
- EasyARM2131开发板源码之一-----------6.GPIO输出实验-LED数码管显示0-F字符，同时控制LED1、LED2、LED3、LED4显示对应的16进行值-EasyARM2131 one source development board ----------- 6.GPIO experimental output - digital LED Display 0-F characters and control LED1, LED2, LED3, LED4 shows the
HK910-test
- 掌宇公司44b0实验平台的测试程序，共16个程序,包含led,数码管，开关，串口，蜂鸣器，实时时钟，键盘中断，ADC，网卡，PS2键盘，UC/GUI-company 44b0-yu palm experimental test platform, with a total of 16 procedures, including led, digital control switches, serial, buzzers, real-time clock, keyboard interrupt,
DATARETljx
- LED数码管显示0-F字符，同时控制LED1、LED2、LED3、LED4显示对应的16进行值。数据以高低位调换. 串口UART0接收上位机发送的数据，接收到返回最后一个数据到上位机，同时中断计数显示，显示回发上位机的数据。 周立功lpc2104板开发。-digital LED Display 0-F characters and control LED1, LED2, LED3. LED4 shows the corresponding values for 16. Data-transf
5digital-led-sweep
- ATMEGA16使用的5位数码管动态扫描程序。
LED
- C8051f330的数码管显示
DISPLAY
- S08例程：本程序是显示模块的例程，所接器件为四位八段led数码管，其中PTB0-PTB3 与数码管的位选相连接，PTB4，PTB5与74LS164连接
Ledhex
- LED数码管显示0-F字符，同时控制LED1、LED2、LED3、LED4显示对应的16进行值。-digital LED Display 0-F characters and control LED1, LED2, LED3, LED4 shows the corresponding values for 16.
LPC2200_experiment_AIN0+disp+led
- 在MagicARM2200实验箱上实现的模拟温度报警实验。通过采集实验箱上W1的电压信号，将测量结果转换后通过数码管显示当前值，当测得的结果超过上限或下限时，实现8栈LED灯的闪烁报警。-MagicARM2200 experiment in the realization of the simulation box on the experimental temperature alarm. Experimental box through the acquisition of the volt
PINLVJI
- 利用51单片机实现数字信号频率周期测量，用LED数码管显示-The use of 51 single-chip digital signal frequency cycle measurement, digital control with LED display
led
- mcs51单片机的led驱动程序 数码管的特性-mcs51 lcd
DigitalClock
- 描述: 简易电子时钟，LED数码管显示 K1---时调整 K2---分调整 上电时初始化显示: 12-00--Descr iption: Simple electronic clock, LED digital tube display K1--- adjust K2--- sub-adjusted initialized at power display: 12-00-00
work2
- 动态显示6位LED数码管，按键0-E时，在LED上显示按键序号开始6个编码对应的LED显示内容；按F时清除显示。-Dynamic display of six LED digital tube, keys 0-E, the key number in the LED display started six codes corresponding to the LED display by F, clear display.
led
- 使用DSP芯片TMS320F2812来控制数码管-TMS320F2812 DSP chip to control the use of digital
18b20-with-LED-display
- 18B20 详细程序 已通过测试 并且附有 数码管显示温度的功能-18B20 detailed procedure has been tested with a digital display and the function of the temperature
2011-3-29Test-5
- 这是基于飞思卡尔xs12芯片写的一个电阻电容电感测量程序，用数码管显示测量值，led灯表示量程-This is written based on a Freescale xs12 chip resistors and capacitors inductance measurement procedures, measurement with digital display, led lights that range
STM32-7SEG-LED-SCAN
- 8位数码管动态扫描显示实验(显示不用库函数) *显示用指针直接访问GPIO端口的输出寄存器，形式GPIOD->ODR *延时delay_nms(5)时，显示不闪烁 *74HC138 A--P2.2--PE.0 B--P2.3--PE.1 C--P2.4--PE.2 *74HC573 D0~D7---PD[0..7] LE---PE.3 *by 追梦 2011-4-3-8-bit digital dynamic scan showed that the experimen
led_liushui.mcp_0_backup
- LED的流水灯程序设计，LED数码管显示-This register is used for specific configurations on memory remap. Two bits are used to configure the type of memory accessible at address 0x0000 0000. These bits are used to select the physical remap by software and so, byp
LED共阴_随机数
- 实现基于树莓派的共阴4位数码管驱动，使用语言为PYTHON,使用硬件资源为树莓派GPIO，面包板和杜邦线若干(Implementation of the raspberry based 4 bit digital tube drive)
10月18日
- 摁1输出矩键，摁2stm32单片机上的两个灯亮，摁3的蜂鸣器一直响，摁4 4个led灯隔一秒闪烁，摁5，蜂鸣器响三秒，摁6，数码管显示数字六 1 矩键 C.01234567 + 2 亮灯 B5.E5 + 3 蜂鸣器 B8 + 4 4个灯走马灯 1秒 F.3579 共阴极 + 5
MSP430驱动6位数码管程序
- 使用MSP430驱动LED数码管C语言程序，便于移植。(Using MSP430 to drive LED digital tube C language program, easy to transplant)