搜索资源列表
Adc_Uart1
- This will sample all 8 A/D-channels. The result will be send out via UART1 and can be seen within any terminal-program (9600 Baud). With each pressed key the next channel will be converted. No interrupts are used.
F33x_ADC0_ExternalInput_Mux
- For C8051F330 This code example illustrates using the internal analog multiplexer to measure analog voltages on up to 8 different analog inputs. Results are printed to a PC terminal program via the UART.
RS232
- RS232接口的抄表终端程序的VB代码尽量不要让站长把时间都花费在为您修正说-RS232 interface to the meter reading terminal program' s VB code you can use the table solve the problem
out
- S51单片机串口通信的51端程序，实现接收PC发来的数据并让它在1602液晶上显示. -S51 51 Serial Communication terminal program to achieve to receive the data sent by PC and liquid crystal display it in 1602.
frenquencycounter
- 利用终端的频率计程序，J2X8C显示，键盘输入，液晶输出-Frequency counter using the terminal program, J2X8C display
serial8051
- a program for displaying ADC values,counter and blinking mode via serial communication from the 89C51 micro controller to the hyper terminal program on the PC
advanced-serial-port-monitor
- rs terminal program with rs 232 via windows application
LM4324-B0M
- pc terminal program for microcontroller
Terminal-consumption
- 浴室计时消费 终端机程序 ID卡 不需下载数据 -Bathroom the timing Consumer Terminal program ID card without downloading data
wsnclamp_test
- STM8S单片机搭载tinyos系统，实现无线组网（终端程序）、电流采样。电流采样采用感应式平均值算法，最大精度1 。编译后可以直接使用-The STM8S microcontroller equipped the tinyos system, wireless network (terminal program), the current sampling. The current sampling Induction average algorithm, maximum precision
Touch-screen-main-program
- 触摸屏主程序，主要是触摸屏通过串口控制单片机实现控制，另一个串口主要是对控制的数据进行无线传输，通过zigbee无线收发模块传送到接收端进行数据处理，整个系统的程序是超市只能购物系统的原型，通过此程序的设计能够实现简单的超市智能购物。-Touch screen main program, the main is a touch screen is controlled through serial control microcontroller, another serial port for
F06x_ADC2_ExternalInput_Mux
- C8051F060 内部多通道切换开关测量8路不同电压的程序.测量电压结果,并通过串口打印功能将测量结果传到计算机终端.-This code example illustrates using the internal analog multiplexer to measure analog voltages on up to 8 different analog inputs. Results are printed to a PC terminal program via the
program
- 公交基于GPS自动报站比赛一等奖程序,亲自编写且测试通过，可靠好用-automatical bus terminal broadcasting
code
- 此为温湿度采集终端程序的完整实现，调试成功。实现了modbus协议03号命令的数据采集，采用STCSTC15F2K60S2单片机，使用了简单的具有优先级的任务调度系统，温湿度传感器型号为AM2302,,温度和湿度通过74HC595静态显示驱动的四位数码管轮流显示，2个按键单击1次可分别查看温湿度的最大值和最小值，uart1作为调试端口，数据通过uart2经过max485实现485通信。-This is the temperature and humidity acquisition termin
prg2051
- Using this programmer you can program the internal flash of the microcontroller AT89C2051 from Atmel. The AT89C2051 programmer is connected via the serial RS232 interface to a PC. In comparison with other programmers, you do not need a special softw
Concentrator-terminal-program
- 本程序是电力行业配变终端集中器的程序，协议规约是376.1规约。功能有载波抄表、485抄表，GPRS远程通信、以太网通讯。冻结数据、终端数据定时上报功能。还具有交流采样功能。 电能表 、集中器、采集器一体的抄取电表的系统。通过设置不同电表号及中继号，抄取整栋楼的电能表读数-This program is focused on the power industry s distribution transformer terminal procedures, the agreement Sta
MT6070iH-and-MCU-Modubus-RTU
- 威纶工业触摸屏MT6070iH 与单片机Modubus RTU通信协议解析 及相关触屏端和单片机端的程序。触屏端程序用EasyBuilder8000 解压 单片机端程序用Keil打开。 让您的项目中增加更强的用户体验。 -Wei Lun industrial touch screen MT6070iH and Modubus MCU RTU communication protocol analysis and related touch screen client and single pro
rcc522-P-12864-Peepromv1.0
- 使用RCC522 与12864，51，单片机构成的学校实验室门禁系统终端程序,可以实现储存卡片。卡片管理。学号输入-Use RCC522 and 12864,51, access control system consisting of terminal program microcontroller
bootloader
- 将给出一个实际的的Boot Loader程序，它可以配合Windows中的超级终端程序，采用Xmodem传输协议，通过RS232接口下载更新用户的应用程序。(This section will give a practical Boot Loader program, which can cooperate with the super terminal program in Windows and use Xmodem transport protocol to download and up
STM32F407ZGT6-PROJECT
- 基于stm32f407最小系统版，可以实现基本的灯光语音控制主控端程序(The basic control terminal program of light voice control can be realized)