搜索资源列表
gpseep
- 微程序控制器采用ATMEL AVR MEGA162，该MCU为双串口，16 k字节系统内可编程FLASH，512字节EEPROM等。MCU工作流程为：(1) 上电复位，初始化各输入输出端口，定时器，串口等；(2) 初始化GPS，输出数据仅保留RMC；(3) 初始化GPRS，设置服务器IP地址，端口；(4) MCU循环读出来自GPS的数据，通过GPRS发送至服务器。
gprs
- 关于单片机（51系列）通过GPRS模块（LT8030）和服务器进行通信-on SCM (51) via GPRS module (LT8030), and communications servers
430gprsFUN.rar
- 本例主要使用MSP430F1612 实现了驱动Q24plus GPRS终端 连接到服务器端 进行数据通讯,MSP430F1612 used in this case the drive to achieve Q24plus GPRS terminal to connect to the server-side data communication
gprs
- 基于SIM300 单片机GPRS通讯 51c语言演示程序。程序演示如何向服务器通过GPRS发送信息。-gprs communications program, the client is 51C
GPRS
- 通过GPRS模块向服务器发送数据,内容包括服务器IP地址和端口的配置。-Deliver data to the sever depend on the GPRS model
using-GPRS-to-send-GPS-data
- 显示GPS信息并等待短信启动通知，通知来临时 主动连接远端服务器 将GPS信息传至远端服务器 传送方式为GPRS-GPS and wait for the SMS startup notification, notice to temporarily take the initiative to connect to a remote server to the GPS information transmitted to the remote server to send for GPRS
Through-the-GPRS-send-datar
- 这是一种通过GPRS向服务器发送数据的代码.-This is a via GPRS to the server, sending the data code.
AA
- 此程序是基于SIM300模块的GPRS开发程序，功能是通过GPRS想服务器发送数据-This procedure is based on the SIM300 GPRS development process server to send data via GPRS want
STM32F103RCT6
- STM32从串口读出温度数据，再通过UDP或GPRS上传服务器-STM32 temperature data read from the serial port, and then upload server via UDP or GPRS
SIM900A_GPRS
- sim900a建立GPRS连接，并通过IP地址与上位机服务器进行数据传输-sim900a establish a GPRS connection, and IP address with the host computer via the server for data transfer
SIM900A_GPRS_Domain
- sim900a通过域名进行GPRS连接，并于上位机服务器进行通信-sim900a GPRS connection through their domain names, and in the host computer to communicate with the server
GPRSDATA
- 本设计采用STC12C5A60S2单片机作为主器，采用SIM300作为GPRS数据传输模块。通过GPRS数据流量方式向中心服务器发送数，本设计采用UDP方式传送数据-STC51 GPRS
code
- 基于stm32的GPS项目，通过GPS获取定位信息，将信息通过GPRS传输到服务器，也可通过串口传输，非常好用，程序没有错误，可下载直接使用-Based on the stm32 GPS project, through the GPS positioning information, the transmission of information through GPRS to the server, can also be via a serial port transmission, is
ZStack-CC2530-GPRS_GateWay
- 结合zigbee与GPRS sim900功能，在Zigbee协议栈基础上对应用层进行开发，通过串口将Zigbee采集到的电压、温度数据转发给gprs，再经gprs远距离传输至服务器端。-Zigbee combined with GPRS sim900 function, based on the Zigbee protocol stack developed for the application layer, through the serial port Zigbee collected v
GPRSwenshidapeng
- 四个从机检测温湿度和光照度，通过nrf24l01发送到主机，主机通过nrf24l01接收并在2.8寸tft上显示，最后主机通过gprs模块把收到的信息发送到电脑tcp服务器。-Four slave detect temperature, humidity and light intensity, sent via nrf24l01 to host, received and displayed on a 2.8-inch tft, finally host through gprs module
gprs
- gprs，数据通过GPRS上传到服务器 ，有心跳包，上传协议-gprs, data is uploaded to the server via GPRS, a heartbeat packet, upload protocol, etc.
GPRS-connection-to-the-server
- GPRS连接服务器，普通单串口单片机程序，本程序运行后如果gprs模块找到服务商信号，就会连接指定的服务器。-GPRS connection to the server, ordinary single serial microcontroller program, after the program runs if gprs module to find service providers signal, it will connect to the specified server.
gprs
- 通过单片机控制网络模块，通过GPRS网络向服务器发起数据请求，使用前检查晶振大小是否合适。-Through the MCU control module network, through the GPRS network to the server initiated request data, use check before the crystal size is appropriate.
IOT_stm32
- stm32控制gsm的gprs功能发送数据到服务器-stm32 contorl gsm s gprs send data to server
STM32实现GPRS数据传输
- STM32实现GPRS数据传输，1. 上网连接服务器2.发送短信(STM32 implementation of GPRS,1. connect to server 2. to send SMS)