搜索资源列表
C汇编的上电初始化
- 单片机C语言的上电初始化，这确实是个头疼的问题!-microcontroller on the C language -- initialization, it is indeed a headache!
CAN 的调试程序
- CAN的调试程序。CAN的初始化重要包括下面几个方面。RXB0SIDH，RXB0SIDL，RXB0MIDH，RXB0MIDL。这是接收过滤器。TXB0SIDH，TXB0SIDL，TXB0DLC，这是发送标志位。还有波特率寄存器。操作模式为 正常模式。-CAN debugging procedures. CAN initialization important aspects include the following. RXB0SIDH, RXB0SIDL, RXB0MIDH, RXB0MIDL
12887的初始化程序——89C51
- 12887的初始化程序——89C51，有助于各位使用12c887芯片！大大加快开发进度！-12,887 initialization procedures -- 89C51 help you use 12c887 chip! Progress greatly accelerated development!
9850
- KeilC51编程,51与DDS芯片 AD9850的接口程序.包括对DDS的初始化以及输出控制.-KeilC51 programming, and 51 AD9850 interface program. DDS including initialization and output control.
P89C51RD+14
- //P89C51RC+、P89C51RD+特有例子//初始化错误或通信错误等待1秒，让 //pc程序超时并报告错误-/ / P89C51RC, P89C51RD specific examples / / initialization error or wait for a communication error seconds, / / pc overtime procedures and report errors
MMC-c
- AVR单片机下的mmc卡控制程序，包括系统SPI模式初始化，使卡进入SPI模式及检测等-AVR cards under the VAT control procedures, including the systematic SPI mode initialization, access cards and SPI mode detection
96SYSINT
- 在80C196单片机下初始化液晶驱动器SED1335子程序-under the 80C196 LCD Driver initialization subroutine SED1335
NCJP
- 对ＣＡＮ的ＳＪＡ１０００的初始化，可以发送数据-right SJA1000 CAN initialization, can send data
CS5534
- ad采集芯片5534的源代码，初始化，包含了基本的操作-ad Acquisition chip 5534 source code initialization, including the basic operation
p18f4610
- 有关MICROCHIP的P18F4610一些初始化程序．包括RAM初始化，定时器的使用及中断的使用．开发环境是MPLAB编译器是MCC18．希望对新手有帮助少走弯路．-going before the P18F4610 some of the initialization process. RAM including initialization, the timer interruption of use and use. Yes MPLAB development environment c
HX8347_HX8340_HX8367
- 奇景HX8347 HX8340 HX8367的初始化程序(注：一般MCU彩屏有了初始化程序，其他部分程序都是相同的)-Places HX8347 HX8340 HX8367 initialization procedure (Note: General MCU initialization procedure has color, the other part of the program are the same)
lcdinit
- 驱动IC为：s6e63d6x的OLED液晶（c0283qglc-t），基于2440的SPI初始化配置代码-Driver IC for: s6e63d6x the OLED LCD (c0283qglc-t), based on the 2440 configuration of the SPI initialization code
RTL8019ASDemo2
- 单片机控制RTL8019AS实现以太网接口实例，改程序用C编写。原理图用protel设计。 包括以太网初始化程序、发送程序和接收数据程序。 单片机系统为整个电路的主处理部分，其作用主要包括对以太网接口芯片的初始化配置 以及以太网数据的发送和接收控制。-SCM RTL8019AS Ethernet interface, an instance, change program written with C. With protel schematic design
1B-R8C1A-the-timer-X-initialization-
- R8C1A 1B的定时器X初始化子程序以及中断函数。-R8C1A 1B X initialization routine and the timer interrupt function.
c8051F340-port-initialization
- c8051F340 端口初始化 Target: C8051F340, F341, F342, F343, F344, F345, F346, F347 // Tool chain: Keil // Command Line: None-c8051F340 port initialization Target: C8051F340, ' F341,' F342, ' F343,' F344, ' F345,' F346, ' F347//
C8051F-MCU-initialization
- C8051F020单片机初始化程序和编译步骤-The C8051F020 MCU initialization procedure compilation step
ESC-initialization
- 电调初始化程序 不是用遥控器，而是用pmw直接控制-ESC initialization not by remote control, but with pmw direct control
C8051F060-initialization-procedure
- C8051F060初始化程序，包括端口看门狗定时器串口晶振-C8051F060 initialization procedures, including serial port Watchdog Timer oscillator
STM32--System-clock-initialization
- STM32F103 系统时钟初始化 系统滴答时间-STM32f103 System clock initialization
AN10404_1
- lpc2000 启动代码 说明，对编写boot代码，或者研究对应的平台很有用哦(Initialization code lpc2000)