搜索资源列表
IARprojects
- NRF24L01通过STM32单片机进行通信的收发程序，本人测试通过，绝对可用-NRF24L01 STM32 MCU to communicate by sending and receiving process, I tested, absolutely free
usart
- iar下使用STM32 通过串口把NRF24L01发送的数据显示在PC上-iar to use the STM32 NRF24L01 sent through the serial port data on the PC
NRF24L01-for-ucgui
- STM32 2.4g nrf24l01 cortex-m3
NRF24L01-Code
- NRF24L01模块STM32驱动，2.4G无限传感模块-NRF24L01 module STM32 drive, 2.4G unlimited sensing module
NRF24L01
- 使用stm32控制无线传输模块NRF24L01实现短距离的信息传输。-Use the the stm32 control wireless transmission module NRF24L01 achieve short-distance information transmission.
NRF24L01-unwire
- 使用stm32神舟4号开发板通过无线模块NFR24L01控制另一个模块动作-Use stm32 Shenzhou 4 development board through wireless module NFR24L01 control another module action
STM32-NRF24L01-DS18B20
- stm32 nrf24l01 ds18b20 pwm-Write your own remote control robot ultrasonic ranging module procedures DS18B20 measurement procedures, NRF24L01 wireless communication drivers, and so on. STM32-based program.
nrf24l01
- 24L01无线模块芯片的驱动程序，STM32控制发送接收-24L01 wireless chip driver module, STM32 control the transmission and reception
NRF24L01(recive)
- 基于STM32的NRF24L01的多对一通信（多个发送一个接受），此为接收端的程序-Based of STM32' s NRF24L01 many-to-one communication (multiple transmit an acceptance), this is the program receiving end
NRF24L01-send1
- 基于STM32的NRF24L01的多对一通信（多个发送，一个接收），此为发送端1的代码。-The STM32 s NRF24L01 the many-to-one communication (multiple sending, one receiving), this is the sender a code.
NRF24L01-send2
- 基于STM32的NRF24L01的多对一通信（多个发送，一个接受），此为发送端2的程序。-The STM32 s NRF24L01 the many-to-one communication (multiple send an acceptance), 2 This is the sender program.
NRF24L01-STM32
- 本实验将实现如下功能：开机的时候先检测NRF24L01模块是否存在，在检测到NRF24L01模块之后，根据KEY0和KEY1的设置来决定模块的工作模式，在设定好工作模式之后，就会不停的发送/接收数据，同样用DS0来指示程序正在运行。-The experiment will achieve the following functions: start when the first detection NRF24L01 module exists, is detected NRF24L01 modu
stm32-base-station
- STM32 基站程序，用于接收信号，并通过串口传给上位机，无线模块采用nRF24L01-STM32 base program for the received signal to the host computer via the serial port, using the nRF24L01 wireless module
nrf24l01
- STM32开发板测试程序,包括LED、lcd,nrf24l01,-STM32 development board test program, including the LED, lcd, nrf24l01,
stm32 - nRF24L01
- stm32F103c8t6关联nRF24L01无线射频模块进行无线中继，使用单片机引脚为SPI口，方便有效。(stm32F103c8t6 associated nRF24L01 radio frequency module for wireless relay, using the microcontroller pin for SPI port, convenient and effective.)
奋斗STM32开发板TINY例程
- STM32奋斗板-LED闪烁： 演示了LED定时闪烁例程。并附带例程详解及实验手册PDF STM32奋斗板-LED闪烁-ucos： 基于ucos 演示了LED定时闪烁任务，可通过串口1修改闪烁间隔。并附带例程详解及实验手册PDF STM32奋斗板-TIM3-CH2： 演示通过TIM3的CH2通道产生特定频率的波形。并控制LED闪烁。并附带例程详解及实验手册PDF STM32奋斗板-TIM3-PWM： 演示通过TIM3的CH2通道产生PWM波形，控制LED的明暗变化。并附
STM32控制nRF24L01+与USB模块通信
- stm32驱动nrf24l01代码,本人多次使用，想要学习使用2401的同学可以下载。(nrf24l01 driver code based on stm32)
STM32无线接收（测试成功）
- 基于stm32f103的nrf24l01通信(NRF24L01 communication based on STM32F103)
NRF24L01
- 利用MDK5开发软件，编写的STM32驱动NRF24L01进行无线传输输出，包含了接收和发送两个工程(Using MDK5 development software, the STM32 drives NRF24L01 for wireless transmission, including two projects for receiving and sending.)
STM32遥控器
- 该程序实现 adc对双轴传感器的X轴Y轴电压的采集，并用不同的标志位代表双轴传感器不同位置时的电压，利用SPI协议将采集到的数据传递给NRF24L01模块，利用NRF24L01模块将数据发送给下位机，实现与下位机之间的通信。(The program realizes the acquisition of the Y axis voltage of the X axis of the dual axis sensor by ADC, and uses the different symbol bi