搜索资源列表
pwm-led
- 通过按键加件PWM频率，来控制电机转速或者调灯亮度等，并显示到LED PIC16F74-PIC16F74 PWM-LED
STM32_LED
- 基于STM32控制的LED灯按键闪烁 c语言程序-press keyboard to control LED program that base on STM32
Key-control-led-cc2430
- 物联网必学 CC2430开发板得一个实验例程 实现功能为按键控制LED灯闪烁 开发环境应为 IAR Embedded Workbench-Things will have to learn CC2430 development board features an experimental routine to achieve control of LED lights flashing for the key development environment should be IAR Embed
KeyBoard
- STM32F103ZET6 矩阵键盘控制LED灯，1-8按键点亮LED1-8,9-16按键关闭LED1-8-STM32F103ZET6 matrix keyboard control LED light 1-8-key light LED1-8 ,9-16 button to turn off LED1-8
key-led
- 按键程序通过IO口来读取按键的状态，并根据读取的键值用IO口来控制led灯的亮和灭，使用的是CORTEX-M3核心板和lm3s6965的MCU，在keil中编译下载即可运行。-Key program through the IO port to read the button state, IO port read key to control the led lights turn on and off, using the CORTEX-M3 core board and lm3s6965
mian
- avr单片机，M16.三个按键，中间长按可以打开和关闭灯的闪烁控制。当打开后，当按左边键时，LED灯闪烁一次；当按中间键时，LED灯闪烁两次；当按右键时，LED灯闪烁三次。-avr microcontroller, M16 three keys, in the middle, long press to open and close the lights flashing control. When opened, press the left button, LED light flashes
GPI474O
- 本例程主要测试LED和KEY，当程序运行时，LCD屏上会显示： STM32F10x DEMO GPIO TEST 按键K1-K4控制灯闪动的次数： 按k1,L1,L3各闪1次 按k2,L1,L3各闪2次 按k3,L1,L3各闪3次 按k4,L1,L3各闪4次 -The main routine test LED KEY, when the program runs on the LCD screen will display: The STM32F10x DEMO
Traffic-lights
- 本模拟系统由单片机硬/软件系统组成，利用单片机AT89S52作为核心元件，两位八段数码管显示倒计时间，发光二极管LED灯用来指示东西南北车辆通行状态，按键控制电路用来实现紧急或是特殊情况的处理，较好的模拟了交通路面的控制.-The simulation system consists of the MCU hardware/software systems, the use of single-chip AT89S52 as the core component, two eight digit
led
- 按键控制lcd灯的编程，通过按键的控制是lcd屏显示相应的内容-failed to translate
1
- 按键控制LED单灯闪烁实验，适合初学单片机者使用。-Control button LED single lamp flashes experiments, suitable for beginners to use microcontroller.
GPIO_KEY
- 按键控制led灯的亮灭，运用对按键的查询来判断其按键的按下与放开，读入状态，来控制0-3号灯的状态。-Bright led lights off button control, use of key query to determine its press and release the button, read status, the status lights to control 0-3.
BLE-CC254x-1.2.1---Light
- LED灯和按键结合通过蓝牙4.0实现无线通信传输，达到工业级控制水平-LED lights and buttons combine wireless communication via Bluetooth 4.0 transmission, reaching the level of industrial control
LED
- 有源音箱的设计，51单片机 两个按键增减LED灯亮的个数程序，还有同时控制音量大小的程序-Two buttons increase or decrease the number of LED lights program, as well as control the volume while the size of the program
IO
- 用按键控制LED，KEY1按一次LED1亮，两次LED1、LED2亮，三次LED1、LED2、LED3亮，以此循环；过程中KEY2按下，点亮的灯熄灭。-With keypad control LED, KEY1 press LED1 lit twice LED1, LED2 lights, three LED1, LED2, LED3 light, this cycle process KEY2 Press, lit the lamp goes out.
The-8-keys-to-control-8-LED-lights
- 通过单片机上的独立按键来控制8个LED灯，同时也可以通过哪个灯亮反映是第几个按键按下-Through the single independent key to control 8 LED lights,At the same time, can also through which light reflected is the first of several key press
LCD12832-driver
- 本测试程序是在44B0板子附带的LCD程序例子修改而来。其中LCD.C全部重写。 本程序用于在S3C44B0板子上点亮NT7534驱动的13264带ICON图标的黑白液晶屏。 除此之外，本程序将流水灯程序和按键控制LED灯程序也放在一起。-LCD12832 driver Source Code
liushui
- 通过编程来实现单片机I/O口对LED的控制，使流水灯显示上下流动、停止流动、闪灯等功能，并由按键控制流水灯的不同亮法，LED的工作方式通过键盘的扫描实现。其中的LED采取共阴极接法，通过依次向连接的LED的I/O口送出低电平来实现 LED的点亮。-Programmed to achieve single-chip I/O port for LED control, so water light show upward and downward flow, stop the flow, fla
5
- 通过IAR编程实现zigbee模块两个按键无线控制LED灯-Zigbee module to achieve two key wireless control of LED lights programmed by IAR
liushuideng
- 8个独立按键分别控制8个led灯，通过程序控制让灯亮灭循环闪烁。-Eight separate buttons control the 8 led lights, program control make lights flicker off cycle.
F310_frame
- 通过对按键的扫描 实现频率显示和led灯闪烁(Realizing frequency display and led flicker by scanning the key)