搜索资源列表
430
- 430配合数字电位器使用，整个工程文件，已测试通过。-430 Digital Potentiometers with the use of the whole project documents have been tested.
shuzidianweiqi-danpianji
- 详细介绍了数字电位器原理与单片机的接口设计-Digital Potentiometers Interface Design Principles and SCM
ccsc_dcp_lcd
- 使用PIC 16F877A及CCS-C语言编写的可以在ICD/MCD2 DEMO板上运行的应用程序，可以以RB0按键控制数字电位器（Xicor X9C102）改变电阻、并在DEMO板的1602 LCD上实时显示效果。-PIC 16F877A and the use of CCS-C language ICD/MCD2 DEMO board can run applications, key control can Rb0 Digital Potentiometers (Xicor X9C102)
51x9013
- 数字电位器x9c103的驱动,该驱动可以调高调低-Digital Potentiometers x9c103 drive, the drive can be increased to reduce
DAshiyan
- 用ADC0809完成模拟信号到数字信号的转换。输入模拟信号由A/D转换单元可调电位器提供的0～5V，输出数字量显示在显示器屏幕上-Complete with the ADC0809 analog to digital signal conversion. Input analog signal by the A/D conversion unit adjustable potentiometer provided 0 ~ 5V, digital output displayed on the m
ADshiyan
- 用ADC0809完成模拟信号到数字信号的转换。输入模拟信号由A/D转换单元可调电位器提供的0～5V，输出数字量显示在显示器屏幕上。显示形式为：AD0809：IN0 XX。 -Complete with the ADC0809 analog to digital signal conversion. Input analog signal by the A/D conversion unit adjustable potentiometer provided 0 ~ 5V, digital out
Digital-voltmeter
- 数字电压表：利用模数转换芯片ADC0832实现，输入电压经89k电阻和10k精密电位器分压，测试电压为0～51v，可用表校对-Digital voltmeter: the use of analog to digital conversion chip ADC0832 achieved, the input voltage through 89k and 10k resistors precision potentiometer divider, a test voltage of 0 ~ 51
MCP41010yudanpianjiat89c51
- MCP41010与单片机at89c51联合控制LED灯的亮度，数字电位器与单片机联合应用-MCP41010 and microcontroller at89c51 joint control the brightness of the LED lights, digital potentiometer with a microcontroller application
TPL0501
- TI公司的TPL0501数字电位器芯片的驱动源程序代码-TI' s TPL0501 digital potentiometer chip driver source code
prj_DS1666_test
- DS1666 数字电位器，通过编程可以改变电阻值，用于程控改变放大倍数，音量等应用中。测试51单片机通过，观察输出wiper和low terminal两端的阻值，呈现增大然后减小的趋势。-DS1666 digital potentiometer, the resistance value can be changed by programming for programmable magnification change, volume and other applications. 51 si
DCP-C-for-X9313W-Driver
- 数字电位器C程序X9313W驱动程序.doc-DCP C source
X9C103_C51
- 数字电位器在51单片机的驱动,实现数字控制电阻等-x9c103 and 89c51
X9421Keil
- 单片机控制X9421数字电位器，基于C++语言，在Keil环境下完成，希望对你有所帮助！-SCM control X9421 digital potentiometers, based on the C++ language, the Keil environment is complete, I hope to help you!
spi
- 通过数字电位器实现整个电路的运放功能，进而提高整个电路的计算精度-Via digital potentiometer entire circuit op amp function, thereby increasing the accuracy of the entire circuit
模拟spi控制数字电位器
- 利用单片机通过模拟SPI线控数字电位器，使数字电位器输出想要的电阻值。(Using MCU to simulate SPI wire controlled digital potentiometer)
shuzidianweiqi
- arduino通过蓝牙手机端控制三路数字电位器x9c103，inc脚接D4，D7，D10，（控制级数），U/D脚接D3，D6，D9，（控制方向），CS脚接D2，D5，D8，（选择器件），本程序设定30步一次，可以根据需要自行调节，一共100步，如有不周之处还请指教。(Arduino through the Bluetooth mobile terminal control three digital potentiometers x9c103, Inc feet to D4, D7, D10,