搜索资源列表
sys_020
- 风向风速和温度要素的采集计算和存储，并把计算所得的数据通过串口发送出去。-Wind direction wind speed and temperature of computing and storage elements of the collection, and to the calculated data sent through the serial port.
Test_BatterySensor
- 基于JN5139这款SOC芯片的数据采集程序，利用GAINSJ开发套件上的温湿度传感器，将测得的温度，湿度值通过PC机的串口调试助手最终显示到PC机上。开发环境为Jennic CodeBlocks软件，使用C语言编写。-This SOC based on JN5139 chip data acquisition program, using GAINSJ development kit on the temperature and humidity sensors, the measured t
5883L-test
- CC2530通过I2C通信接收HMC5883L采集的数据，并通过串口发送给电脑，亲自调试测试可用。-CC2530 received by the I2C communication the HMC5883L data collected and sent to the computer through the serial port, personally commissioning tests available.
ADXL345-test
- CC2530模块通过I2C通信接收ADXL345传感器采集到的数据并通过串口通信传递给电脑，亲自调试测试可用-CC2530 module through the I2C communication receiver the ADXL345 sensor to the data passed to the computer through the serial port communication, the person commissioning tests available
MT-UART
- 通过对Z-SATCK协议栈中串口处理程序的修改，完成了，对GPS模块串口数据的采集- 您是不是要找： 通过对Z-STACK协议栈中串口处理程序的修改,完成了,对GPS模块串口数据的采集 中文(简体)英语日语 By Z-SATCK protocol stack serial processing modifications complete, the GPS serial data acquisition module
C8051F060-AD-UART1
- C8051F060 自带高速AD进行数据采集 可达100兆采样率 并切缓存与片外ram 并把采集数据通过串口发送给PC - Data Acquisition example for C8051F060 Descr iption: This example illustrates the use of ADC1 and the DMA to acquire and store data. It is intended for use with the C8051F060
compass-AND-gps
- 通过avr实现对compass和GPS数据的采集，通过串口发送出来-Avr achieved by compass and GPS data collection, sent out through the serial port
ZStack-CC2530-2.5.1a
- CC2530，协调器建立网路后终端自动加入，将传感器数据发送给协调器，PC通过串口控制zigbee温度采集启动与停止.-CC2530, coordinator after the establishment of the network terminal is automatically added, the sensor data are transmitted to the coordinator, the PC through the serial port control ZigBee
2-zigbee_cc2530
- 终端节点每隔一段时间采集一次片内温度值，并将结果发送给协调器，同时亮一下led1；路由节点每隔一段时间采集一次电池电压值，并将结果发送给协调器，同时也亮一下led1；协调器每收到一个无线数据，就亮一下led2，同时将数据通过串口发送给电脑。是“LED”，则也亮一下led1。-............................................. no
ZigBee--stack-driving-sht20
- ZigBee终端节点驱动sht20温湿度传感器采集数据，并将数据利用ZigBee协议栈发送到ZigBee协调器，协调器节点将接收到的数据通过串口显示到pc机。-ZigBee terminal node drive sht20 temperature and humidity sensors to collect data, and the data is sent to the use of ZigBee protocol stack ZigBee coordinator, the coordi
Com_Vb
- 接收串行数据的单片机上位机程序。使用VB编写，解析单片机发送过来的串行数据。 单片机是8052,搭载了TCS3200光学颜色采集器，将采集到的数据通过RS232发送到PC，显示RGB数值，在label控件中显示该RGB数值的颜色。 串口数据格式是RGB24位加一位识别码/-Receive serial data microcontroller PC program. Using VB to write, parse microcontroller serial data sent ove
MMA7455
- 利用CC2530实现IIC总线通信协议采集三轴传感器MMA7455数据，读取MMA7455的数据，并通过口串口在上位机显示 -Use CC2530 implement IIC bus communication protocol data acquisition triaxial sensor MMA7455, MMA7455 read data through the serial port on the PC display
STM32_UCOSII_EDP_LWIP
- 本代码是stm32通过enc28j60网口模块讲单片机串口取到的温度数据传送上物联网平台Onenet。stm32串口接收端的数据是来自cc2530无线采集到的。物联网平台采用的是Onenet的edp协议。网口传送是用lwip协议。资料中含说明文档，stm32工程文件-The code is stm32 speak to take on a single-chip serial temperature data transfer through networking platform Onenet
SensorCollector
- zigbee,实现温湿度传感器数据的采集，并且可以通过串口在PC机上查看相应的数据(ZigBee, the temperature and humidity sensor data acquisition, and can be through the serial port to view the corresponding data on the PC machine)
stm32 MMS8451
- MMA8451三轴加速度计 STM32F103c8t6单片机控制程序，可以设置加速度计量程，±2g、±4g、±8g，但是程序里2g和4g模式下精度很高很准确，8g模式下采集到的数据存在问题，通过串口打印输出，显示单位是g。程序内关键部分已添加注释，希望可以帮到大家。(MMA8451 three axis accelerometer STM32F103c8t6 microcontroller control program, can set the accelerometer range, + 2