搜索资源列表
nRF24E1程序
- nRF24E1作为 RF处理芯片，内带51处理器，其频段处于ISM频段，通信速度可以达到1M，可以进行跳频处理，在短距离高速度通信上有非常良好的功能。-nRF24E1 as an RF chip, which with 51 processors, the band at ISM band, communication speed can reach 1M, can Hopping, a short distance high-speed communications on a very goo
CAN-ucos
- 将CAN现场总线移植到UCOS2中的驱动程序，在BC中调试运行成功-CAN fieldbus will be transplanted to UCOS2 the driver, were in BC successful operation Debugging
MCP2510CAN
- ARM7 MCP2510的CAN程序-ARM7 MCP2510 CAN procedures
2407c(CAN)
- TMSLF2407局部控制器模块(CAN)程序，C语言
CAN
- CAN通讯:该程序实现发送缓冲器0向接收缓冲器0发送数据的自测试模式，其中接收采用中断方式 发送采用查询方式
CAN
- 周立功smartArm2300开发板中CAN总线示例程序。
CAN
- 80c196单片机的CAN初始化及收发程序
can
- 基于LPC2378的CAN通信程序，实现两个CAN的自发自收
Flash存储器W25X16,W25X32,W25X64读写擦除程序
- 大容量Flash存储器W25X16,W25X32,W25X64读写擦除程序，在SST单片机上测试通过，使用了SST单片机的硬件SPI功能；也可以使用虚拟SPI的方法，在SST和STC单片机上测试通过。-Large-capacity Flash memory W25X16, W25X32, W25X64 erasable read-write procedure, SST Singlechip test is passed, the use of SST Single-chip hardware
kk飞控板程序，已经调通
- kk飞控板程序，已经调通，可以实现全部飞行功能-kk flight control panel program, has been transferred through, you can achieve all flight functions
AVR单片机SPI接收程序
- AVR单片机SPI接收程序，改程序开发环境是CVAVR。该软件具有强大的代码生成能力，大家可以试着自己生成代码！,Single-chip SPI receiver AVR procedures, program development environment is changed CVAVR. The software is a powerful code generation capability, we can try to generate their own code!
C17_MSCAN12SelfTest
- 写得非常好的HCS12 CAN程序，可以直接用于工程项目.-HCS12 CAN write a very good program, can be directly used for projects.
AD7705(C51)
- 1，初始化： 如果AD7705复位引脚直连VCC，最好在初始化程序中加入初始化序列，不然ready信号不会输出。 2，输入范围 如果AD7705采集单端信号，则输入必须在0到VDD之间，而不可以超出或为负，如果一个输入为负，则另一个输入会有灌入电流的现象，芯片无法正常运行。-AD7705 is a complete 16-bit A ö D converter. Within Structure in Figure 1. If the external crysta
STM32_CAN
- STM32 CAN测试程序，程序已经编译过，通过测试，有测试模式和正常运行模式-STM32 CAN test program, the program has been compiled, tested, with test mode and normal operation mode
pic18f2480(can)
- CAN总线程序代码，测试OK的，可以直接使用-CAN Bus program code Have been tested OK please rest assured use
CAN
- 此程序为09年底新出的STM32F107嵌入式微控制器的CAN实验程序，使用Keil RVMDK 3.80a 集成开发环境开发-This program is the end of 2009 out of STM32F107 new embedded micro-controller CAN experimental procedure, using Keil RVMDK 3.80a Integrated Development Environment Development
2010.5.11-AD-CAN-LCD
- 此程序是在电子白菜的STM32开发板上实现的，采集电位器模拟量，经过AD转化，然后发送到CAN上-This program is in the electronic cabbage STM32 development board to achieve, capture analog potentiometer, after AD conversion, and then sent to the CAN on the
F50x_CAN0_Receive
- c8051f500 CAN 程序例子，硬件环境为新华龙c8051f500 评估板 有改动验证过。-c8051f500 CAN program example, hardware environment for the new evaluation board with changes Hualong c8051f500 verified.
CAN
- 一个基于LPC2200的CAN程序 可发送数据-LPC2200 s CAN-based procedures can send data
CAN
- 通过该程序实现CAN功能自测,实现自发自收的功能。-CAN selftest.