搜索资源列表
27c512
- 用于LED点阵屏的中文字库.有制作点阵屏的同志请看,这是一个HEX的文件.-LED Display Screen for the Chinese font. Making a lattice screen comrades See, this is a HEX document.
mbm12864LCD
- 128*64液晶屏原理图：宏泰128*64液晶屏；配10个按键；每个按键配3个LED指示灯；模仿西门子做的；-128* 64 LCD screen: 128* 64 Hongtai LCD with 10 keys each button with three LED indicator light do imitate Siemens
LED-C
- 2字点阵屏，单片机驱动实现移动显示，采用154进行列驱动，单片机Px口实现行驱动。-2 character dot-matrix screen, single-chip mobile display drivers, the use of 154 for out-driven, single-chip line driver Px I to achieve.
LED_Test
- 51单片机驱动 LED屏程序 Protues仿真-51 MCU LED screen program, Protues Simulation
1dianzhenguanggaopai-1.0
- 通过vb设计上位机软件 实时改变led点阵屏要显示的内容-Through the vb design PC software real-time change of led dot matrix LCD display content
LED-graphic-screen-PCB
- LED图文屏以显示文字、符号、图片为主，其信息是在计算机上经专用软件编辑生成，经通讯口传输到控制器，保存在FLASH存储器中，再由控制器脱机循环播放。-LED graphic screen to display text, symbols, pictures, mainly, the information is edited on a computer generated by special software, the communication port transfer to the c
DS18B20
- 基于AT89S52下的DS18B20检测温度，用6位数码管显示实际温度值和符号，当检测到DS18B20不存在或者有问题时，蜂鸣器将报警，数码管黑屏-AT89S52 based on detection of temperature under DS18B20, with six digital displays the actual temperature values and symbols, as detected DS18B20 does not exist o
LED
- 在msp430上如何使用1602液晶屏程序-In msp430 LCD screen on how to use the 1602 program
ledDisp
- 在单片机上驱动通用的1/16动态扫描的LED屏，LED口为Hub08通用口，单色1024点屏。驱动芯片为HC138和HC595.该代码硬件环境为STM32，但若在其它单片机上使用，只要改动一些管脚配置代码即可。-Microcontroller-driven general 1/16 dynamic scan LED screen, LED port for Hub08 generic mouth monochrome 1024 screen. Driver chips for the HC138
LED-dianzheng
- 采用51单片机为控制芯片，74HC595和74HC164为辅助芯片对LED点阵屏进行控制-51 single-chip controller chip, 74HC595 and 74HC164 auxiliary chip LED dot matrix screen control
led
- LED滚动广告显示屏显示驱动程序，多个16*16LED显示演示程序，实现多个16*16LED屏的多个字符显示,显示方式有整行上移、帘入帘出、左移、右移。 -Advertising display LED scrolling display driver, and more than 16* 16LED display demo program, more than 16* 16LED screen character display, the display of the entire l
LED-RF2401_sci-AT45
- AVR单片机ATMAGE16，PC串口发送命令给RF2401模块，通过射频传给点阵屏显示数据，中文字库保存在AT45内。-AVR microcontroller ATMAGE16, PC serial port to send commands to the RF2401 module, pass through the RF matrix screen display data stored in the AT45 Chinese character within.
led
- 按键控制lcd灯的编程，通过按键的控制是lcd屏显示相应的内容-failed to translate
STM32LED
- STM32F103RB 32位单片机驱动 32点阵LED屏 显示Keil uVision4 ARM C语言代码-STM32F103RB 32-bit microcontroller drive 32 dot matrix LED display Keil uVision4 ARM C language code
LEDxianshizijimingzi
- 走在大街上，不管是大商场还是小店铺，都能看到好多电子LED屏，这个程序就是教你如何用单片机编写-Walking down the street, no matter how large or small mall stores, can see a lot of electronic LED screen, this program is to teach you how to write MCU
led
- 内有20多个仿真图，程序，用于调试LED屏-There are more than 20 simulation diagram, the program for debugging LED screen
pcb-led
- led屏显示的代码和原理图，包括主程序，头文件，使用51单片机-led screen display code and schematics, including the main program, header files, use the microcontroller 51
1602-led-i2c-demo
- 1602液晶屏，通过i2c实现通信的控制源码，c语言版-1602 LCD screen, through the i2c communication control source code, c language version
MC9S12XSaDS18B20
- 此程序为基于飞思卡尔MC9S12XS和温度传感器DS18B20位硬件基础进行的温度采集程序，并通过LED屏显示结果-This program is based on Freescale MC9S12XS and temperature sensor DS18B20 bit hardware based on the temperature acquisition process, and through the LED screen display results
Electronic-circuit
- 3. 创建一个工程文件，编程实现将0 1 2 E F、姓名等显示在LCD屏上，编程实现将3到4位数据小数点后保留一位（如10.2、100.6）分别显示在三组LED屏上。 4. 编程实现按键输入功能，将按键信号显示在LED或LCD屏上，（如按▲键，,使屏幕信号逐渐加1，从0加到10，再按▼键，从10减到0。 5. 编程实现D/A转换（下行通道），输出（4~20mA）电流，并进行0点和斜率校正。 6. 编程实现A/D转换（上行通道）实现数据采集，将采集信号显示在LED和LCD屏上。程序要