搜索资源列表
minicom_User
- minicom 是linux 操作系统下的串口终端程序 是和Windows 操作系统的下 超级终端功能相近的程序 不过比超级终端功能要强 下面我们通过命令行 介绍minicom 的操作方法-Minicom Linux operating system is the serial terminal program is the Windows operating system and the next Super Terminal functions similar procedures
HyperTerminal
- 基于8051单片机的超级终端仿真 超级终端，其实就一个输入输出设备，搞ARM的，这个东西可能再熟悉不过了，XP下就自带了一个，在 程序->附件->通讯工具->超级终端，可以看到。 我们通常是用基于串口的超级终端，即通过串口实现输入输出，来与CPU交互，控制CPU的执行。 -Super-based terminal emulation 8051 HyperTerminal, in fact, on an input output devices, engage
enet_lwip
- lm3s9b90的lwip演示程序，由于lm3s9b90没有显示屏，需要由超级终端来查看开发板的ip地址-lm3s9b90 of lwip demonstration program, as lm3s9b90 no display, requires the super terminal to see the ip address of the development board
VisualizationToolExample
- Code Warrior 5.1环境下应用VisualizationTool可视化调试的一个例子。-This project is an HC12 ANSI-C project. This example is running the "Demo" program on: -the CodeWarrior HC12 Simulator, (choose "Demo (Simulation)" target), -ICD12 P&E cables interface (ICD12
SampleSwitch
- cc2530zigbee中AH控制端开关程序，很多人开发板缺少按键，这个程序将程序中按键控修改为rs232命令控制，字符‘2’是绑定指令，字符‘1’是开关控制指令。-cc2530zigbee in AH switch control terminal program, many people lack key development board, the program will modify the program button control rs232 command and contro
SampleSwitch
- cc2530zigbee中AH控制端开关程序，很多人开发板缺少按键，这个程序将程序中按键控修改为rs232命令控制，字符‘2’是绑定指令，字符‘1’是开关控制指令。-cc2530zigbee in AH switch control terminal program, many people lack key development board, the program will modify the program button control rs232 command and contro
little-car-send
- 小车采用STC12C5A16S2（主单片机）可以实现测量前方障碍物的距离，并实时发送给从单片机STC89C52，之后从单片机通过串口发送给电脑，此文件为发射端程序 -Car used STC12C5A16S2 (main MCU) can measure the distance between the front of the obstacle, and real-time to the slave microcontroller STC89C52, then sent from the mi
pic18f2550-usb-izole-triyak-kontrol-ccs-c-visual-
- Than 8 switch outputs Port B of the PIC18F2550 is used. Power gets the circuit from the USB port. Power supply is separate from the microcontroller and the computer galvanically. switching signals USB socket intended as a virtual serial port COM4. To
jpeg
- 基于spce3200的jpeg编解码头文件程序-SPCE3200 JPEG codec terminal file program based on
shu-ma-guan
- 动态扫描数码显示程序 P0口接J3，数据端口 P2.2接 J2 B端子，表示段码锁存 P2.3接 J2 A端子，标志位码锁存- Dynamic scan digital display program P0 port access J3, data port P2.2 connected J2 B terminals, which means that the code segment latch P2.3 connected J2 A terminal flag c
pc_8535a8515
- 基于ATmega8535和8515芯片的PC机键盘演示程序 MCU:AT90S8515和8535 晶振:8MHZ 使用ICCAVR的终端调试窗口观察PC键盘数据 -Based on the PC keyboard demonstration program of ATmega8535 chip MCU: AT90S8515 crystals: 8 MHZ Use the ICCAVR debug window observing the PC terminal keyboard d
test
- si4463+stm32源码，传输距离为2000米。 这个为终端程序，包含发送和接受。-Si4463+stm32 source code, the transmission distance is 2000 meters. This is a terminal program, including sending and receiving.
Internet-Time-Check
- 江苏新终端断电后，数据项和相关参数就会变得混乱。导致程序运行不正常。本操作为了节约电池掉电后数据丢失的情况。-Jiangsu New terminal after power failure, data entry and related parameters will become confused. Cause the program to run properly. The operation to save the battery power-down data is lost.
18b20_6_chal
- 基于MSP430F5438a单片机 6路18B20采集温度 通过24L01传输 包含发送端接收端程序 接收端利用共阴极8位8段数码管循环显示6路数据 并通过串口传送到计算机- Microcontroller based MSP430F5438a 6-channel temperature acquisition by 24L01 18B20 transmission contains the sender receiving end program receiving terminal co
shuzidianweiqi
- arduino通过蓝牙手机端控制三路数字电位器x9c103，inc脚接D4，D7，D10，（控制级数），U/D脚接D3，D6，D9，（控制方向），CS脚接D2，D5，D8，（选择器件），本程序设定30步一次，可以根据需要自行调节，一共100步，如有不周之处还请指教。(Arduino through the Bluetooth mobile terminal control three digital potentiometers x9c103, Inc feet to D4, D7, D10,