搜索资源列表
SL811_slave
- 采用SL811（工作在slave模式）实现USB设备的firmware参考源码。-use SL811 (in slave mode) to achieve the USB device firmware Participation source test.
c51usb
- 一个用C语言编写的usb程序,测试可以运行,内附有原理图-a C language prepared by the usb procedures, test run, enclosing a diagram
lpc214x-test
- 这个是基于lpc214x的usb的上位机应用程序，分别用逻辑端点1和2发送接收16和64字节
speedTest.速度测试的固件和上位机代码
- CYPRESS USB CY7C68013 的速度测试的固件和上位机代码 上位机用c++,CYPRESS USB CY7C68013 speed test firmware and PC host computer using the code c++
USBHost-S3C2440.rar
- s3c2440a usb host 测试程序，ADS编译环境，可以识别usb设备，从u-boot移植过来的.,Usb host test src for s3c2440,derived from u-boot,compile with ads
LPC1768-Xplorer
- LPC1768-Xplorer is a CORTEX-M3 based stamp board for NGX’s mbed-Xpresso Baseboard. The LPC1768 microcontroller has 512KB of internal flash and 64KB RAM. Ethernet MAC, USB Device/Host/OTG interface, 8-channel general purpose DMA controller, 4 UARTs, 2
usb-device-massstorage-project-at91sam7s-ek-iar.zi
- Include startup files and peripherial devices Code for Atmel ARM7 development-At91SAM7S Series Test Code for Mass Storage USB device under IAR platform
USBtestspeed
- 这个代码是别人写的，为了测试USB的从机发数据到主机的数据，上位机和单片机的代码都有。-This code is written by someone else, in order to test USB data issued from the machine to a host of data between host computer and microcontroller code for both.
Dev_io
- Contains the source files to build simple development board I/O sample. The purpose of this software is to demonstrate how to use the buttons and LED on the EZ-USB developer s kit. See the readme.txt file located within the directory for detail
EZUSBFirmware
- 自己买的USB CY7C68013A 的开发板资料 随后还有他的源码 和大家一起分享测试程序源代码（包括VC工程文件及Firmware）.rar-He bought the USB CY7C68013A development board data source and then have his share test program source code (including the VC project file and Firmware). Rar
EZ_USB1
- 自己买的USB CY7C68013A 的开发板资料 随后还有他的源码 和大家一起分享 测试程序源代码。-He bought the USB CY7C68013A development board data source and then have his share test program source code.
stm32V1_2
- 这是我自已为实验室画的基于STM32的PCB，现在将原理图及PCB全部分享，图是用PROTEL 99SE绘制的。可能会有布线不合理之处，仅供大家参考。 实验板资源介绍 1）CPU为100脚STM32F103XX 2）TFTLCD 3）SD卡 4）4X4键盘模块及四个独立按键 5）ISP下载口及20脚JTAG下载口 6）RS232接口、RS485接口、PS/2接口、USB接口 7）I/O口驱动的蜂鸣器 8）I2C口驱动的AT24C02 9）
minimus_led_test
- Test working minimus usb at90usb162
C51USB
- 用C51单片机USB实例源码代码通过测试。-C51 Microcontroller with USB example source code through the test.
STM32USB_PC-
- STM32F103实现USB与PC之间的双向通信，已调通，三个端点，包括上位机测试软件-STM32F103 realize the two-way communication between USB and PC, has been transferred through, the three endpoints, including test software
PL2303__v1.5.0
- 一个win8能用的usb转串口驱动，亲测可以用，安装完后，请打开“控制面板”->搜索“设备”（在控制面板右上角的搜索栏里输入“设备”即可）,然后在弹出的对话框中选择“否，让我选择要执行的操作”->选择“从不安装来自Windows的更新程序驱动软件”（保持“自动获取设备应用以及设备制造商提供的信息”选中）-A Win8 can use the USB-to-serial driver, pro-test can be used after the installation, open
STM32F4Discovery-VD-USB
- stm32f407discovery 开发板实现usb与电脑的通信 包括了上位机的测试软件 -stm32f407discovery usb development board to achieve communication with the computer, including a test of PC software
USB-Read-Data
- USB开发 上位机读取USB设备端点数据 亲测可用-USB development PC to read the USB device endpoint data pro-test available
USB
- STM32嵌入式系统的USB读卡器应用试验程序，-USB card reader embedded systems application test program
3158
- Including orbital maneuvering simulation, initial orbit calculation, Single path or multipath Rayleigh fading channel simulation, Undergraduate complete set requirements refer to the standard test models.