搜索资源列表
VS1003
- VS1003音频解码芯片为VS10XX系列的第三代产品，是芬兰VLSI Solution Oy公司生产的单片MP3/WMA/MIDI解码和ADPCM编码芯片，它内部包含一个高性能、低功耗的DSP处理核（VSDSP），一个工作内存，一片可供用户程序使用的5.5KB RAM，一个串行SPI总线接口，一个高质量的采样频率可调的过采样DAC以及一个16位的采样ADC.-VS1003 Audio Decoder Chip for VS10XX series of the third-generation
ADC
- MSP430F149的ADC模块，序列通道多次转换，转换好的值用1602显示，实测可用，绝不坑爹。-MSP430F149 ADC modules, serial channel number conversion, the converted value with the 1602 show, the measured available, not pit father.
ARM7-ADC
- LPC21xx ARM7 ADC 内置ADC使用串口发送-LPC21xx ARM7 ADC built using serial ADC Send
tempteture
- here is the sorce code and circuit daigram for tempreture meter based on thermistor and serial adc ltp1298 or mcp3201. -here is the sorce code and circuit daigram for tempreture meter based on thermistor and serial adc ltp1298 or mcp3201.
multidaq
- adc 0808 interfacing to 8051 microcontroller using keil compiler...multi channel data is displayed on pc terminal through serial communication
ADC_HRON
- ADC. Test sorce Code For Serial Adc. Test (0831) in ASM.
Test_ADC
- JN5139芯片自带的ADC接口（12bit），最快采样频率27.8K，该程序将GAINSJ开发套件上的模拟电压（电池电压）通过ADC转换成数字信号，并通过串口传到PC机上显示出来。开发环境为Jennic CodeBlocks软件，采用C语言编写。-JN5139 chip onboard ADC Interface (12bit), the fastest sampling frequency of 27.8K, the program will GAINSJ Development Kit o
stc4510DAQ
- LabVIEW9.0版本编写上位 KEIL4.0编写的单片机ADC采集程序 通过串口发送到电脑端-LabVIEW9.0 version prepared by the host microcontroller ADC KEIL4.0 acquisition program written sent to the PC via the serial port
MSP430danpianjiCprogramingdesign
- 实用的基础msp430的模块程序C语言编程 包括基础时钟，ADC,DAC单通道单序列，多通道多序列等，锁相环，异步串行，，FLASH擦写，中断，比较捕获，PWM波形的产生，LCD模块程序，行列式键盘，基本定时器，DMA数据传输捕获脉冲信号周期等-Practical basis for msp430 module C programming, including basic clock, ADC, DAC channel single sequence, such as multi-chann
ON-CHIP-PROGRAMS_PIC16F877
- the contents are pic16f877 programme for ADC, PWM and SERIAL TX and Rx-the contents are pic16f877 programme for ADC, PWM and SERIAL TX and Rx...
ADC-ADS7841
- Serial AD/DA程序先通过IO送一组数字数据到DA芯片进行转换，然后将转换结果送入到AD芯片进行转换。-The Serial AD/DA program first to send a group of digital data through the IO to the DA chip to convert, and then converted the results into the AD chip to convert.
MSP430F149_complex
- 基于MSP430F149的综合通讯程序，目的是通过ADC采集传感器的输出，经标定算法最后通过串口232与上位机通信，以及DAC7512的模拟电压控制输出。代码调试通过，包含以上所有功能，适合做430单片机采集程序的框架-MSP430F149-based integrated communications program, the purpose is the acquisition of the sensor output by an ADC, the calibration algorithm
ADC
- 基于STC12C5A60S2单片机内部AD模块采集 简易数字电压表 12864串行通信显示-AD module microcontroller based STC12C5A60S2 acquisition, simple digital voltmeter, 12864 serial communications display.
adc
- msp430AD采样后发送采样数据通过串口到PC-msp430AD sampled and sent to the PC via the serial port sampling data
ADC
- 神州3号开发板 ADC采样电压 通过串口 超级终端显示采样的电压值 -Shenzhou-3 development board ADC sampling voltage through serial HyperTerminal display sampled voltage value
STM32-ADC
- STM32开启DMA进行ADC转换，并透过串口上传转换的数据，-STM32 open the DMA ADC conversion and uploading data through serial conversion,
MSP430F149ADC-and-yejingxianshi
- ADC序列通道多次转换12864液晶程序适合msp430f149-ADC serial channel program suitable for multiple conversions 12864 msp430f149
ADC
- 1路AD单次采集(采用串口调试助手显示) 用串口调试助手向单片机发送AD命令,单片机 接收到命令后将读取ADC0的电压值返回给计算 机在串口调试助手上显示.-1 channel AD single acquisition (using serial debugging assistant display) AD send commands to the microcontroller using serial debugging assistant, SCM After
ADC
- XS128的A/D模块编程 利用两个AD口分别于电位器连接，调节电位器，将采集到的值通过串口发送到PC-A/D XS128 module programming using two AD ports are connected to potentiometer, adjust potentiometer, the collected value through the serial port to send to PC
ADC
- STM32F10X系列 ADC的采样，包括DMA等-STM32F10X serial ADC sample，contentDMA and so on