搜索资源列表
pbp_interupt
- 使用PIC Basic Pro语言开发PIC单片机应用程序时使用Timer中断的应用实例-PIC Basic Pro language used to develop single-chip microcomputer PIC application using Timer interrupt the application of
PS2_driver
- Ps/2 keyboard driver written in CCS C f黵 PIC.. interrupt driven
int-PWM
- PIC单片机PIC16F676外部中断与定时中断同时使用PWM输出程序源码，有详细说明，欢迎下载学习。-PIC16F676 PIC microcontroller with an external interrupt timer interrupt program source code while using the PWM output
pic_01
- PIC单片机INT中断的程序参考，一个INT中断应用的简单示例程序。-INT interrupt the program PIC microcontroller reference, a simple example INT interrupt application procedures.
can_232
- 通过串口接收中断，如果接收到的数据流为14个数据，同时第一个数据为0x72，则把收到的后13个数据通过PIC内部CAN控制器，以标准帧或扩展帧的格式发送CAN总线上。-Through the serial port receive interrupt, if the received data stream is 14, while the first data for the 0x72, put the data received by the PIC after the 13 interna
Ringtone-16f-pic-micro
- /* This code was designed for a clock speed of 20MHz */ /* The target device was a PIC18F452. */ /* You can use the PIC16F877 by changing the setup of CCP1 to */ /* CCP_COMPARE_INT. You will also need to toggle the output pin in the */ /* CCP
PIC-_BLDCM_Interrupts
- 汽车电动窗无刷直流电机中断控制程序，很好用的。已经通过验证。-Car electric window brushless DC motor interrupt control procedures, very good use. Have been authenticated.
Interrupts
- PIC单片机一段关于中断的代码，仅供参考。-PIC microcontroller paragraph on the interrupt code, for reference only.
zhongduan
- 用PIC单片机内部定时器0，作为16位定时器使用，并开启溢出中断。单片机的外部中断0引脚接开关SW2，并设置为下降沿的触发方式。单片机的UART接口工作于全双工异步模式，1个起始位，8个数据位，1个停止位，波特率为9600，并开启接收中断，与PC机通信。编写程序实现功能：SW2按键按下时，LCD上显示“Timer0 Start”, 定时器0开始工作，然后LCD上显示“Timer0 Working”,当UART接收到PC机发送的命令“P”时，定时器0停止工作，LCD上显示“Timer0 Stop”
ADC
- PIC单片机AD中断程序和AD软件滤波的程序实现-PIC microcontroller interrupt routine AD and AD filtering software program
chapter6
- PIC编程实例第六章，包含3个程序，如下：S061: INT 中断例子 S062: B口高四位中断例子 answer: 习题编程题例程 - PIC programming examples in Chapter VI contains three programs, as follows:
chapter7
- PIC编程实例第七章，包含4个程序： S071: TMR0定时中断例程 S072: WDT例程 S073: 习题编程题电路图 answer: 习题编程题答案-PIC programming examples in Chapter VII, includes four programs: S071: TMR0 timer interrupt routine S072: WDT routine S073: Exercise circuit diagram progr
chapter8
- PIC编程实例第八章，包含4个程序： S081: 采用查询方式把模拟通道AN0的10位A/D转换结果送D口，C口显示 S082: 采用中断方式把模拟通道AN0的10位A/D转换结果送D口，C口显示 S083: 测量电位器RV2对地阻值并显示在四位数码管上。 answer: 习题编程题答案-PIC programming examples in Chapter VIII, contains four programs: S081: using queries AN0 anal
task-6
- This program is written for Microchip pic 18F452 microcontroller . It shows how to configure a timer and use its overflow feature for interrupt generation .
Timer
- PIC 12F675 Timer Application. Very useful to understand timer0 module & interrupt routin. Compiler : mikroC also include circuite diagram.-PIC 12F675 Timer Application. Very useful to understand timer0 module & interrupt routin. Compiler : mikroC