搜索资源列表
STM32的硬件I2C比较难用
- STM32的硬件I2C比较难用，此模拟I2C可以实现其功能，但速度不及硬件。-STM32 more difficult to use the hardware I2C, I2C this simulation can achieve its function, but the speed is less than the hardware.
STM32中文固件库,用中文注释
- STM32中文固件库,用中文注释，英语不是很好的，可以下来看看。不用啃英文。。,Chinese STM32 firmware library, notes in Chinese, English is not very good, you can look at it. English do not bite. .
stmPWM
- STM32的PWM输出的例程，设计时候可以作为参考-STM32 of the PWM output routines can be designed as a reference when
STM32_CAN
- STM32 CAN测试程序，程序已经编译过，通过测试，有测试模式和正常运行模式-STM32 CAN test program, the program has been compiled, tested, with test mode and normal operation mode
2010.5.11-AD-CAN-LCD
- 此程序是在电子白菜的STM32开发板上实现的，采集电位器模拟量，经过AD转化，然后发送到CAN上-This program is in the electronic cabbage STM32 development board to achieve, capture analog potentiometer, after AD conversion, and then sent to the CAN on the
an2557
- stm32实现了串口IAP功能，可以应对不同的硬件平台！-stm32 realized serial IAP function, you can cope with different hardware platform!
stm32_gui_lib
- The STM32 Embedded GUI library enables designers, comfortable with the use of standard microcontrollers, to create higher-end “look and feel” human interfaces by replacing conventional electromechanical switches with touch sensing controls.Designers
STM32-usart-programm
- STM32串口程序USART，自己调试成功的，可以运行，通过与电脑串口相连，可以观察传输的数据-STM32 serial program USART, the success of their own debugging, you can run through a computer serial port, data transfer can be observed
CAN
- 基于STM32的CAN通信源码，很详细。便于学习。-STM32 CAN-based communication source, very detailed. Easy to learn.
cdma-6-9
- 基于STM32平台的CDMA的串口通讯，CMAD命令已调试，可以使用。-Based on the STM32 platform of CDMA communication, to debug, can use.
gcc-stm32
- stm32在gcc编译器下进行开发的一个例子，很简单的点灯，可在万利stm32f10b的板子上跑-An led operation example of stm32 compiled by gcc which can run on Manley stm32f10b board successfully.
an2820
- stm32控制双极性步进电机程序可以实现控制方向和转动的速度！-stm32 bipolar stepper motor control program can control the direction and speed of rotation!
stm32fatfs
- 在sd卡上移植fatfs,移植成功，已经能用，-FatFs is a generic FAT file system module for small embedded systems. The FatFs is written in compliance with ANSI C and completely separated from the disk I/O layer. Therefore it is independent of hardware architecture. It ca
SHIBQ1.0
- 本代码是基于STM32的示波器的代码，能够实现在LCD上显示和触摸操作。-This code is the code based on the STM32 oscilloscope, can be achieved on the LCD display and touch operations.
Based-on-STM32--MP3-player
- 基于STM cortex-M3的架构的MP3，能实现菜单管理，音乐播放，图片查看功能。-Based on the structure of the STM cortex-M3 MP3, can realize the menu management, music playback, the picture to see function.
STM32-CH376-Udisk
- 基于STM32的CH376 外扩U盘读取程序，很实用，可以很容易的改造成其他系统的u盘操作程序。-Based on the STM32 CH376 expand outside U disk read process, a very practical and can be easily transformed into other systems u disk operating procedures.
STM32-V3.5.0xiugai
- 经过多年经验把一般情况下能用到的模板进行了总结。同时格式也进行了规范。-After many years of experience under normal circumstances can be used to template a summary. The format is also the norm.
CAN
- 基于stm32 can通讯的程序 主要是回环检测的程序 后面会提供两个板之间的通讯-Based on the stm32 can communication program Mainly behind the loopback detection program will provide the communication between the two plates
STM32-CAN-TXRX
- CAN STM32 上的CAN 收发数据.用队列完成-CAN to send and receive data CAN STM32. Using the queue to complete
CAN-BUS
- STM32 CAN BUS 热插拔调试成功 -STM32 CAN BUS