搜索资源列表
ledSim
- led仿真程序，用于单片机开发时，实时模拟程序运行时LED的显示-led simulation program for the development of SCM, Real-time simulation program running LED display
dirvecontrolofLED
- 该程序是在汉字显示系统中，控制LED显示屏汉字的显示方式式，能够实现左移和静显-procedures in the Chinese character display system, the Chinese control the LED-display mode. be able to achieve significant bits and static
LEDCtrl
- 这是一个测试led的程序,在VC下可以很好的运行 我试过,效果不错
led-dianzheng
- 这是个51单片机驱动led8*8点阵的程序，跟大家分享下-This is the 51 single-chip driver led8* 8 dot matrix program, to share with you the next
werdsa
- 将BLKS内容为首址的连续N个字节数传送至BLKD内容为首址的存储区，数据块传送程序。-BLKS content sites will be headed by a continuous N the number of bytes sent to BLKD content-led site storage area, the data block transfer program.
238060016EE108V02_3b154dee_7097_4a3c_80d0_d52f2a00
- SHARC 处理器的测试程序例程，有借鉴意义-ADSP-21161 processor: 1. Blink- Example LED blink code. 2. Flash programmer- Flash programmer project for ADSP-21161
1616LED
- 16×16点阵(滚动显示) 单片机系列程序-16 × 16 dot matrix (scroll display)
digital-clock
- 系统由AT89C51、LED 数码管、按键、发光二极管等部分构成，能实现时间的调整、定 时时间的设定，输出等功能。系统的功能选择由SB0、SB1、SB2、SB3、SB4 完成。其中SB0 为时间校对，定时器调整功能键，按SB 0 进入调整状态。SB1 为功能切换键。第一轮按动 SB1 依次进入一路、二路、三路定时时间设置提示程序，按SB3 进入各路定时调整状态。定 -System consists of AT89C51, LED digital tube, keys, light
li-hong-deng-xiansi
- 霓虹灯程序，学习发光管变化的程序，希望有所帮助-Neon process, learning LED changing procedures in the hope help
libsvm-mat-3.0-1
- 此为台湾大学林智仁教授及所带领的团队编写的关于svm的程序包，简单实用。-This is the National Taiwan University Professor Lin Zhiren and the team led the preparation of the package on the svm, simple and practical.
i_error
- LED单珠光源的特性对配光具有重要影响，本程序从配光要求这个角度对不同厂家的LED灯的质量进行分析。-the property of LED is very important for using, and the program can envalue the quality of LED light source.
LED_road
- LED路灯配光需要计算许多重要参数。本程序通过利用LED路灯实测数据来讨论这些参数间关系。-lots of parameteres have to be calculated before using the LED road lamp. this program use the measured data to discuss these parameteres.
rgbled
- 基于led数学模型的建立rgbled的光谱仿真模型程序-Led the establish rgbled of the mathematical model spectrum-based simulation model program
ccc
- 短信控制LED程序 gtm 900c mcs 51-gtm 900c mcs 51
hongwai
- DS18B20温度采集然后红外发射出去,接收板接收红外并LED显示接收的数据信息,有完整的发射，接收和仿真程序-DS18B20 temperature acquisition and infrared emission out to receive infrared receiver board and the LED display data received information, a complete transmit, receive and simulation program
dotmatrix2edemo
- 大牛用matlab编的LED灯显示程序，很经典的，希望对大家有用，其实matlab的很多功能我们还没有完全开发出来呢-LED algorithm ,complished by matlab
8-led-and-so-right
- 基于keil软件的8个led灯右移的基本程序-Based on the basic program 8 led lights right of keil software
8-led-lights
- 基于keil软件的8位led灯左移的基本程序-Keil software based on the basic program of eight led lights to the left of
visible-led-communication
- 这里给出了几个可见光通信的MATLAB程序，调制方式采用OFDM调制解调，对于可见光通信的研究者具有重要的参考价值。-Here are a few visible light communication MATLAB program, modulation using OFDM modulation and demodulation for visible light communication researchers have important reference value.