搜索资源列表
ADC0804电压
- 用ADC0804测量模拟电压，电压范围从0V到5V都能精确的测量，该程序已调试成功，可直接运用-ADC0804 measurement using analog voltage, voltage range from 0V to 5V can precise measurement, the debugging procedure has been successful and could be directly applied
AD7416t
- 这是一个用AD7416做的温度测量程序，AD7416是一个数字化温度传感 器。-AD7416 do with the temperature measurement procedures, AD7416 is a digital temperature sensor.
ir（波形测量）
- 1个检测波形的小程序。可以测量波形的长度-a small waveform detection procedures. The waveform can be measured length
通用程序
- cad测量封闭图形面积
tablelookup
- 典型的查表温度测量程序,带有详细的查表原理说明.非常值得参考!-A typical look-up table temperature measurement procedures
chaoshengboceju
- 此超声波测距程序用汇编代码编写，测量精度高，12M晶振可达1mm，稍微修改亦可成为高精度脉宽测量程序，带有仿真图。-The ultrasonic ranging program written in assembly code, high precision, 12M crystal up to 1mm, a slight modification can be a high-precision pulse-width measurement procedures, with a simulat
3
- 基于labview开发环境的 汽车车速测量程序-Labview based on vehicle speed measurement program development environment
RIO-Dynamic-Flow
- 基于NI sbRIO的液面测量程序，仅供参考，需要配合ni9636使用,程序需要自行设置信号输入-Based on NI sbRIO liquid level measurement procedures for reference, need to meet ni9636 use, the program needs to set its own signal input
celiangchengxusheji-V5
- 实现测量工程专业常用的测量程序设计，包括测量平差等-Realization of measurement commonly used measurement engineering program design, including measuring adjustment, etc.
testms5534
- 基于msp430F149单片机，模拟spi，驱动ms5534测量程序。含工程文件方便调用。-Based msp430F149 microcontroller, atmospheric pressure measurement module MS5534 drivers, analog spi, including engineering test program.
turning-tool
- 包括“车刀宽度测量”、“刃倾角测量”、“主副偏角测量”和“前后角测量”程序。-Including Tool width measurement , cutting edge tilt measurement , main and auxiliary angle measurement and front and back angle measurement program.
放电次数
- 通过设置放电门槛，输入原始信号，测量局部放电的放电次数，(The number of discharges measuring partial discharges)
我的应用程序
- 这是一个我自己做的安装程序，任意一台电脑均可安装，安装完成直接打开运行即可，主界面是一个输入用户名，密码即可登陆，登陆完成后，则可实现温度采集，电机调速，光强测量，波形信号的采集等。(This is one of my own setup, any computer can be installed, the installation is complete direct operation can be opened, the main interface is a username, pas
电压测量程序例（ok）
- stm32用ADC测量电压，并在LCD数码管上显示(STM32 uses ADC to measure the voltage and displays it on the LCD digital tube)
阻抗测量源程序
- 用于锂离子电池的阻抗测量，基于labview平台建立的测试程序(Impedance measurement)
GPS和INS联合导航matlab程序
- GPS和INS组合导航MATLAB程序，融合状态向量为平台误差角、位置误差、速度误差、陀螺仪漂移、陀螺仪马尔科夫偏差、加速度漂移共18维向量；测量采用速度-位置法；含有数据(GPS/INS fusion by kalman filter)
频率测量
- 该程序实现频率测量，程序简洁明了，功能强大，适用于教学研究(The program realizes frequency measurement. The program is concise and clear, powerful, and suitable for teaching research.)
labview 3D测量程序
- labview 3D测量程序，很好的源码程序，。
大地测量程序代码
- C#代码，支持不同坐标系统的转换，七参数计算，高斯投影坐标解算
转速的测量
- 用LabVIEW程序进行转速的采集，并能够实现数据显示和波形显示。(Using LabVIEW program to collect the speed, and can realize the data display and waveform display.)