搜索资源列表
24CXXXRW
- 24CXXX存储数码管程序（汇编）51单片机 例程
shumaguanxianshi
- 51单片机，常用程序，数码管显示，做成的头文件
CLOCK.rar
- 51单片机的电子时钟程序，用汇编编的，通过数码管显示,51 Single-chip electronic clock procedures, there is a compilation series
keilc_proteus_time
- keil c编的程序,批proteus 数码管电子钟.-keil c allocation procedure, approved Proteus digital tube electronic bell.
11
- 程序名称：51单片机数码管电子钟汇编程序 简要说明：实现24小时制电子钟，8位数码管显示，显示时分秒-Program Name: 51 single-chip digital control electronics assembler bell briefly Descr iption: achieve a 24-hour electronic clock, 8-bit digital tube display, is displayed every minute
TEMPREATURE_LED
- 51单片机程序，通过18b20检测温度，然后送51处理，变在数码管上显示-51 SCM procedures 18b20 Detect temperature, then sent to 51 deal with change in the digital tube display
8051_jiao_tong_deng
- 基于51单片机的带时间显示和紧急控制的交通灯的设计。 此程序在硬件上调试通，用定时器1延时，外部中断0接紧急控制，R0为100MS延时常数，R2为状态延时常数，8279控制数码管显示时间,用P1口控制双色灯-With 51 single-chip based on the time display and the emergency control of traffic lights design. On this process in hardware debugging pass, w
xianshichengxu
- 51单片机控制四片74hc164数码管显示程序-51 SCM 4 74hc164 digital control program
shuxianbiao
- 多功能数显表 本毕业设计的设计任务为一个多功能数显表。该数显表可以测量和显示气压、冲击频率和耗气量。并且具有RS232接口和时间显示。本毕业设计作品选用AK-4气压传感器和LWGY涡轮流量传感器，通过MCS-51单片机来控制操作，实现信号数据的采集、处理和发送。本毕业设计作品不仅可以将气压、冲击频率、耗气量及时间等数据显示在8个LED数码管上，还会通过RS232串口，将数据发送到PC上。并由PC上的配套程序，将信息数据显示在显示器上，这两部分所显示的数据是完全相同的。其中数字显示时间单位为秒
NON
- 汇编语言写的51单片机程序，实现2位10进制数的加减乘除运算，内含按键扫描和8段LED数码管显示程序段。-51 SCM program written in assembly language, to two decimal addition and subtraction, multiplication and division, the block containing the key-scan and 8-segment LED display.
PERFECT
- 汇编语言写的51单片机水温加热控制程序。内含按键扫描和8段LED数码管显示程序，并有水温控制核心程序。-The water temperature of 51 single-chip heating control program written in assembly language. Containing key scan, and 8-segment LED display program, and the water temperature to control the core pr
51-microcontroller-calendar
- 51单片机汇编语言程序设计 Protues环境下7段数码管,单片机,开关仿真-51 microcontroller assembly language programming 7-segment digital tube Protues environment, SCM, switch simulation
CH452
- 程序功能为51单片机通过三线串口操作CH452，CH452驱动8位数码管正常显示以及显示数据的更新。51单片机通过模拟CH452串口操作时序向-The program features 51 microcontroller via a three-wire serial interface operation CH452, CH452 driver 8 digital tube display properly, and display data update. 51 single-chip C
C51_polling
- 汇编写的基于51单片机的A/D采集巡检程序，具有数码管显示、控制，冻结、报警等功能-Assembly based on 51 single chip microcomputer to write A/D acquisition inspection program, with digital tube display, control, freezing, alarm functions
ZHLX
- 51单片机独立式键盘的扫描程序，并在数码管上显示-Independent type keyboard scanning procedures, 51 single-chip microcomputer and digital tube display
xg0322
- 附件代码是51单片机控制数码管的动态显示程序，程序为汇编所写，已经在开发板上进行过认证的。-Annex code is dynamically control 51 single-chip digital tube display program, the program is written in assembler, has been certified development board.
PROJECT_DIANZHEN
- C51汇编语言编写，51单片机控制数码管显示以及控制点阵显示。点阵程序有静态扫描以及纵向滚动两种-C51 compilation of language, 51 MCU control digital display and control the dot matrix display. Dot matrix program has two kinds of static scanning and vertical scrolling
CH451
- 51单片机点亮p口驱动的ch451驱动的数码管和键盘程序-ch451 51spi
数码管显示实验
- 基于51单片机的数码管动态显示程序以及proteus仿真(Dynamic display program of digital tube and Proteus simulation based on 51 single chip microcomputer)