搜索资源列表
18vcharg
- 18v直流充电器控制程序源代码，对电池包具有温度保护的功能-18V DC charger source code control procedures, the battery pack has a temperature protection function
speed
- 无刷直流电动机是以电子换相代替机械换相的直流电动机，它保持了直流电动机的优良特性，具有较好的起动和调速性能，而且它无需机械换相器，使电机的结构简单，可以从根本上克服一般有刷直流电动机易于产生换相火花的弊病-Brushless DC motor with an electronic substitute for mechanical phase of the DC motor, it has maintained the excellent characteristics of DC motor,
bldc
- 无刷直流电机开环程序 电机功率500w 4对极-Open-loop brushless DC motor Motor Power 500w 4 program a very
74hc595
- 此汇编程序实现A/D转换功能，应用于pic单片机上，A/D采用中断方式。该程序通过单片机的RA2模拟通道送入一直流电压，当送入的直流电压大于2.5V时，8个LED闪动，当直流电压恢复到2.5V以下时，LED停止闪动。为了防止干扰，本程序对直流电压采样10次后再作判断，中间的采样结 果用间接寻址的方式存取。-Assembler implementation of this A/D conversion function, applied on pic Singlechip, A/D interru
tuya
- 把桌面当成DC,在上面作图,有兴趣的可以研究下! 非常简单!里面注释写的很明白,我就不多说了-The desktop as a DC, in the above map, are interested in can be studied under the! Very simple! Inside understand written notes, I will not say a
C5402moto
- C5402汇编编写的对直流电机和步进电机进行控制的程序。-C5402 prepared a compilation of the DC motor and stepper motor control procedures.
1
- 采集0-7路输入来自直流源经分压器产生的0～5 V直流电压（可功能扩展，8路可接不同的传感器，采集不同的信号,例如:温度、湿度、图象、声音等）ADC0809将各路模拟信号分别转换成8位二进制数字信号,再对各路数据进行显示。各路通道采集方式为以约5s为周期循环采集（即0路、1路……7路、0路…）约每5ms更新，重新采集一次。显示方式为循环显示和单路显示：开关打开时，循环显示0-7路采集的数据；开关闭合时，显示当前单路采集的数据。3个七段数码管显示结果:最左边的一个数码管DS0显示通道号，其它两个数
pic16f877
- 该程序实现了一种在16f877单片机中控制直流电机的方法-The program has a single-chip 16f877 DC motor control method
cap
- this i the cap of the DSP of texas intrument for control DC motor in a multi axis sytem
LUNWEN
- 设计并制作一个电能收集充电器，充电器及测试原理示意图如图1。该充电器的核心为直流电源变换器，它从一直流电源中吸收电能，以尽可能大的电流充入一个可充电池。-Design and production of electrical energy to collect a charger, charger and test schematic diagram of Figure 1. The core of the charger DC power converters, which flows fro
WAVE6000
- 设计并制作一个电能收集充电器，充电器及测试原理示意图如图1。该充电器的核心为直流电源变换器，它从一直流电源中吸收电能，以尽可能大的电流充入一个可充电池。-Design and production of electrical energy to collect a charger, charger and test schematic diagram of Figure 1. The core of the charger DC power converters, which flows fro
B12V
- 实际用于LED灯，光片控制的直流12V作为输入电源的驱动控制例程。为初学者提供参考-Actually used LED lamps, controlled by DC-12V-ray films as input power drive control routine. Provide a reference for beginners
SVPWMpulse
- SVPWM脉冲产生程序，用matlab的S函数编译，产生ＳＶＰＷＭ的六路脉冲。-SVPWM pulse generation process, using S-functions matlab compiler, resulting in a six-way SVPWM pulses.
DC-003
- 一款使用来电显示电话机程序，FSK和DTMF两种制式-A telephone program to use Caller ID, FSK and DTMF two kinds of formats
firstmotor
- way to use a dc motor using AVR
TLC5615
- 程序名称：TLC5615 实验现象：电机速度由快到慢循环运转。用万用表直流电压档观察VOUT（D10），电压连续循环高低变化。 -Program Name: TLC5615 experimental results: motor speed from fast to slow cycles. DC voltage with a multimeter, observation of VOUT (D10), a continuous cycle of high and low volta
4_MotorDC
- ASM code for PIC16F84A and a DC Motor, includes simulation on ISIS-Proteus
zhiliudianjiwanjie
- 这是一个直流电机的完整程序，可以利用它控制电机的软启动！-This is a complete program of a DC motor, can use it to control the motor soft start!
zhiliudianjitaiosu
- 这也是一个直流电机的程序，适合初学者学习，帮助你提高-This is a DC motor program, suitable for beginners to learn, to help you improve your!!
DC-motor-speed-control
- 通过开关或按键实现三个功能的切换：○1利用A/D转换芯片0809将W1电位器提供模拟量转换成数字量并显示；○2利用D/A转换芯片0832将单片机输出的数字量转换为模拟量输出并显示；○3利用W1电位器提供的模拟量经0809、单片机和0832转换和放大后驱动直流电机，实现电机调速。-Achieve three functions through the switch or button switch: ○ 1 use A/D converter chip 0809 will provide an a