搜索资源列表
another-barcode-scan
- LABVIEW 用摄像头动态扫描条形码，不需要再移动鼠标或键盘框选框框的程序，支持的下载。-The LABVIEW camera dynamic bar code scanning, do not need to move the mouse or keyboard marquee frame of the program, support to download.
IV-curve-measure-with-Keithley2600
- 该程序可用于控制keithley2600数字源表测量太阳电池的IV曲线。可设置正反扫描次数，实时显示测量结果，并计算Jsc，Voc，FF，eff等电池参数。程序IVnew是总程序，除子程序外，还包括NI公司网站上提供的keithley2600程序包（必要）。-The program can be used to control keithley2600 digital source meter to measure the solar cell IV curve. Can be set to t
V2.0
- 位移台的扫描程序，在x，y方向的移动，没隔一段距离，采集一次数据的程序-The displacement station scanning procedures, moving in the x, y direction, no at a distance, capture time data in the process
AFG3000s-Sweep-Frequency
- 利用LabView 程序控制 数字信号源AFG3000进行频率扫描-LabVIEW program control digital signal source AFG3000 frequency sweep
KEIL
- 循环led循环点亮 扫描 用程序控制灯的亮灭-Cycle led cycle light scanning the bright lights of the program control
Barcode_V1.0.11_Src
- 基于labview的图形码扫描程序，启用笔记本摄像头。-Labview-based graphics code scanner enabled notebook camera.
scanner
- 这是扫描枪的通讯实例，可以直接放在程序了，直接用。-This is the communication instance scanner can be placed directly on the program, and direct use.
resonant-frequency-testing
- 通过labview控制信号发生器和锁相放大器进行共振频率检测的程序。freq test.vi实现信号发生器的频率扫描，lockin test.vi 实现锁相放大器的参数设定，数据采集.vi实现锁相数据的采集，waveform arrays to file实现波形数据到文件数据的转换。共振频率测试.vi实现晶振等共振频率的测试-Resonance frequency detection procedures performed by labview control signal generator
transistor-tester-based-on-LabVIEW
- 本文介绍一种基于NI LabVIEW和北京君合泰科技有限公司U18数据采集卡的晶体管特性测试仪的设计方法，内容包含循环扫描数据采集、回扫消隐、多曲线显示、传输系数计算、被测硬件电路设计等，并给出详细的前面板图和程序框图以及三极管、MOS管、光电耦合器等部分器件的特性曲线测试例子-This paper introduces a design method of transistor characteristic tester based on NI LabVIEW and Beijing Jun
osciloscope-data-acquisition
- 通过labview软件可以实时控制示波器器件进行实时的信号采集，程序还可以实现对样品进行扫描-data aquisition with a osciloscope by labview program
SICK
- LABVIEW编写的SICK扫描枪扫码读码程序。-LABVIEW SICK scanner sweep the code read code written procedures.
SICK1
- Labview编写的工控机控制SICK扫描枪读取条码的程序。-Written in Labview industrial computer control SICK scanner reads the bar code application.
扫描枪扫描
- LABVIEW编程中用的扫描枪扫描条码程序(LABVIEW program used in the scanning gun scanning bar code program)
扫描二维码
- 用VISA串口连接扫码枪，用此程序进行通讯，触发读码信号(Connect the scanning code gun with VISA serial port, use this program to communicate, trigger the read code signal.)