搜索资源列表
IV-curve-measure-with-Keithley2600
- 该程序可用于控制keithley2600数字源表测量太阳电池的IV曲线。可设置正反扫描次数，实时显示测量结果，并计算Jsc，Voc，FF，eff等电池参数。程序IVnew是总程序，除子程序外，还包括NI公司网站上提供的keithley2600程序包（必要）。-The program can be used to control keithley2600 digital source meter to measure the solar cell IV curve. Can be set to t
laser-measurement
- 激光测量小程序，日本基恩士激光测距传感器。-laser measurement
reverberation-time
- 室内声学混响时间的测量以及计算labview程序-the measure and caculate of the everberation time of room acoustic
simple-trigger-event
- 这是一个测量扭矩的Labview测试平台程序，每当确定数量的采样完成时，事件结构就会触发，结构内部的处理程序就会运行。如果信号出现异常，就会停止下来。当按下调试按钮之后，程序又会跑起来。-This is a measurement of torque Labview test platform program, complete Whenever determine the number of sampling, the event structure will trigger the stru
frequency-spectrum
- 该程序用于测量频谱。比如可以从扬声器上产生白噪声，用麦克风接收，接收到的数据经过处理便可以生成一个频谱图，程序中带有滤波器。-The procedures used to measure the spectrum. White noise, for example, can be generated from the speaker with microphone receiver, the received data can be treated to generate a spectrum
tempmeasure
- 使用浙大高联CSY-SY生物医学传感器实验箱获取热敏电阻特性曲线，并进行非线性校正，实现温度测量的程序，需要使用labjack U2数据采集盒-Use Zhejiang University Gaolian CSY-SY experimental box for biomedical sensors thermistor characteristic curve, and nonlinear correction for temperature measurement procedures, t
Temperature
- 1.创建一个VI程序模拟温度测量。假设传感器输出电压与温度成正比。使用Demo Read Voltage子程序来仿真电压测量，然后把所测得的电压值转换成摄氏或华氏温度读数。 2.把结果在波形图表上显示 3.在数据采集过程中，实时地显示数据。当采集过程结束后，在图表上画出数据波形，并算出最大值、最小值和平均值。只使用华氏温度单位。 4.修改Temperature Analysis.VI程序以检测温度是否超出范围，当温度超出上限（High Limit）时，前面板上的LED将点亮，并且有一
fangzhen1
- 使用labvIEW编写的测量油井井深的一个仿真程序，通过分析回声信号的频谱，此处使用模拟仿真信号，labvIEW版本7.0-Use labvIEW prepared well depth measurement of a simulation program, by analyzing the echo signal spectrum, signal simulation used here, labvIEW version 7.0
displacemet-measurement
- labview程序，传感器位移测量，可以测量从传感器输出的位移信号，并给出迟滞，线性度，灵敏度等信息，含报表生成。-labview program, displacement measurement sensor can measure the displacement signal output from the sensor, and gives hysteresis, linearity, sensitivity, and other information, including repo
TEMP
- 用该程序可以显示测量所得的温湿度值，并且可将其存入到数据库中-The program can display with temperature and humidity measured value, and it can be stored in the database
singallab
- 基于labview信号处理实验室，能够很好的模拟实验室中波形的读取，有电压、电流的测量，波形的分析，可以进行傅立叶变换，fft变换，此程序已开发完全，可以作为毕业设计使用-Labview-based signal processing laboratory, the laboratory can simulate waveform read, there are measurements of voltage, current, waveform analysis, Fourier transf
3
- 基于labview开发环境的 汽车车速测量程序-Labview based on vehicle speed measurement program development environment
RIO-Dynamic-Flow
- 基于NI sbRIO的液面测量程序，仅供参考，需要配合ni9636使用,程序需要自行设置信号输入-Based on NI sbRIO liquid level measurement procedures for reference, need to meet ni9636 use, the program needs to set its own signal input
turning-tool
- 包括“车刀宽度测量”、“刃倾角测量”、“主副偏角测量”和“前后角测量”程序。-Including Tool width measurement , cutting edge tilt measurement , main and auxiliary angle measurement and front and back angle measurement program.
放电次数
- 通过设置放电门槛，输入原始信号，测量局部放电的放电次数，(The number of discharges measuring partial discharges)
我的应用程序
- 这是一个我自己做的安装程序，任意一台电脑均可安装，安装完成直接打开运行即可，主界面是一个输入用户名，密码即可登陆，登陆完成后，则可实现温度采集，电机调速，光强测量，波形信号的采集等。(This is one of my own setup, any computer can be installed, the installation is complete direct operation can be opened, the main interface is a username, pas
阻抗测量源程序
- 用于锂离子电池的阻抗测量，基于labview平台建立的测试程序(Impedance measurement)
频率测量
- 该程序实现频率测量，程序简洁明了，功能强大，适用于教学研究(The program realizes frequency measurement. The program is concise and clear, powerful, and suitable for teaching research.)
labview 3D测量程序
- labview 3D测量程序，很好的源码程序，。
转速的测量
- 用LabVIEW程序进行转速的采集，并能够实现数据显示和波形显示。(Using LabVIEW program to collect the speed, and can realize the data display and waveform display.)