搜索资源列表
CRC16_Look-up_table_calculation
- CRC16查表法计算，多项式X16+X12+X5+1-CRC16 look-up table method, polynomial X16+X12+X5+1
tcp_file_transfer
- 实现在两台计算机上的数据交换 实现在两台计算机上的数据交换-To achieve the exchange of data on two computers
IV-curve-measure-with-Keithley2600
- 该程序可用于控制keithley2600数字源表测量太阳电池的IV曲线。可设置正反扫描次数，实时显示测量结果，并计算Jsc，Voc，FF，eff等电池参数。程序IVnew是总程序，除子程序外，还包括NI公司网站上提供的keithley2600程序包（必要）。-The program can be used to control keithley2600 digital source meter to measure the solar cell IV curve. Can be set to t
labview
- 计算等径三圆筒电子透镜的电位 复旦大学电子光学课程必备-Potential of the calculation of diameter three-cylinder electron lens electron optics, Fudan University courses necessary
CRC_CALC_CCITT_X25
- 用来计算CRC16校验码（CCITT，欧洲标准）-Used to calculate the CRC16 of (CCITT, the European standard)
calculation-two
- 这个程序是一个关于两个数字相加之和的计算，用的是labview9.0来编写的，这是一个通用的程序，仅供大家参考。-This program is a calculation of the sum of two numbers is labview9.0 to write, this is a common procedure, only for your reference.
image-processing
- 图像处理作为小车走迷宫过程中获得信息的第一过程，对于小车的计算路径和确认位置起到了根本的作用-Image processing information and has played a fundamental role in the process for the calculated path and confirm the location of the car as a car in the Maze process
CRC16_byte_calculation_MSB
- CRC16字节型计算高位先行，多项式X16+X12+X5+1-The CRC16 byte Computing highs first polynomial X16+X12+X5+1
CRC16_byte_calculation_LSB
- CRC16字节型计算低位先行，多项式X16+X12+X5+1-CRC16 bytes Computing low first polynomial X16+X12+X5+1 of
paomadeng
- labvIEW之跑马灯，通过计算来实现，并非使用顺序结构-labvIEW the Marquee, by calculating not use sequential structure
decimal-conversion
- 在labviEW中利用特殊的计算实现2、10、16进制间的转换，界面很适合程序员使用，它将每位二进制分开显示，对寄存器的赋值计算很有帮助-Take advantage of a special calculation in labviEW 2,10,16 hex conversion, the interface is very suitable for programmers to use, it will be separate from each binary register assig
Multi-peak-function
- LabView环境中，峰数计算的例程，.vi文件-LabView for Multi peak function
电机转速计算
- 采用labview编写的电机转速计算器，输入轮胎直径 、减速比、要求车速，输出所需电机转速(Written by LabVIEW motor speed calculator, enter the tire diameter, speed reduction ratio, speed requirements, the output motor speed required)
例5-1 计算n个数据的平方和
- 计算n个数据的平方和，程序为《labview2015程序设计从入门到精通》内的例程，labview2015编译环境下编写的程序，对初学者很有用(Calculate the sum of squares of N data, the program for "labview2015 programming from entry to master" routines, labview2015 compiler environment written procedures, us
例5-2 计算时间差
- 计算时间差，程序为《labview2015程序设计从入门到精通》内的例程，labview2015编译环境下编写的程序，对初学者很有用(Computing time difference, the program for "labview2015 programming from entry to master" routines, labview2015 compiler environment written procedures, useful for beginners
计算峰数
- 利用labview，计算输入信号的波峰数(The wave number of input signal is calculated by using LabVIEW)
地磁计算labview应用程序EXE
- labview调用matlab程序，利用最新的IGRF12球谐系数计算地磁分量的应用程序。无源码。计算结果正确。(LabVIEW calls the matlab program and uses the latest IGRF12 spherical harmonic coefficients to calculate the application of the geomagnetic component. No source code.)
瞬时转速计算
- 提出了如何在labview中实现瞬时转速计算(How to achieve speed calculation in labview)
student_error_detect 1
- 简单的实现比特序列误码率计算，使用的都是很基础的原件，并未使用现成的误码率计算文件(A simple way to computes the bit error rate of a bit sequence.)
计算相位
- 本程序labview2013版本，利用相关性计算两个信号的相位差