搜索资源列表
visa
- 用于上位机与单片机通讯，labview 编写的，很有借鉴意义-Used in PC and single chip microcomputer communication
PC-and-C51
- labview与单片机的VISA通信的简单应用-the labview microcontroller VISA simple communication application
MONITORING-AND-CONTROL--ON-LABVIEW
- 摘 要 针对实现液罐的监测与控制系统，采用下位机：以C52单片机为核心，控制HC-SR04超声波测距模块和DS18B20分别对液面高度和液罐中温度进行测量。上位机：在PC机中通过LabVIEW进行编程，其主要功能为：数字时钟、液罐液位的模拟、波形图、液位超限的报警功能、液位控制的自动和手动模式、以及对数据进行存储。单片机对液位和温度的数据进行采集后，LabVIEW可选择性的使其在面板中进行显示，同时还可发送指令给单片机控制进水阀和出水阀的开闭，也可通过自动模式对液位进行控制。相比于传统控制系统，
MCU_PC_communication
- 采用串口通讯，实现PC机与下位51单片机通信-PC exchange date with MCU through serial port.
PCyudanpianjichuankoutongxin
- 实现PC与单片机串口通信，方便使用，程序易懂-PC and microcontroller serial communication, easy to use, easy to understand program
13.2PPPC
- pc与单片机的监测系统的连接和应用-Monitoring systems, monitoring systems, monitoring systems, monitoring systems, monitoring systems
PCAN-Driver
- 采用Labview编写的上位机界面，应用Peak卡通过CAN总线与单片机进行通信。-Written using Labview PC interface, the application of Peak card via the CAN bus to communicate with the microcontroller.
successWaveform
- 电压尖峰发生器上位机labview语言代码（包含与飞思卡尔单片机的232通讯，逻辑输出控制，触控屏通讯）-Voltage spike generator PC LabVIEW language code
Ultrasonic-Ranging-PC-display
- 通过软件Labview编写前面板和程序框图，通过该面板实现计算机与单片机的串口通信。设置好通信端口，波特率等参数后，超声波传感器检测距离，由单片机进行处理，通过串口将检测的距离输入到计算机，以波形图表显示实时距离，并进行实时存储。-Written on the front panel and block diagram software Labview, Computer and MCU serial communication through the panel. After setting
labview-danpianji
- 利用Keil C51 和LabVIEW编写程序实现PC与单片机串口通信。 设计任务 PC通过串行口将数字（00 ，01 ，02，03... ，FF，十六进制）发送给单片机，单片机收到 后回传这个数字，PC接收到回传数据后显示出来，若发送的数据和接收到的数据相等，则串 行通信正确，否则有错误。启始符是数字00，结束符是数字 FF。-Use Keil C51 and LabVIEW programming to achieve PC serial communication wi
serial-communication
- 本程序为labview开发的PC与单片机串口通信的源程序。-This program was developed by the source PC labview serial communication with the microcontroller.
serial-communication
- 本程序为labview开发的PC与单片机串口通信的源程序。-This program was developed by the source PC labview serial communication with the microcontroller.
STC51
- 单片机烧写程序，很好用，方便实现与pc机的通讯-Burning program MCU, useful,Facilitate communication with the PC
LABVIEW
- 这是运用Labview编写的串口通信的程序，包括PC与单片机，单PC双串口通信，PC与PC串口通信。-This is the use of Labview prepared by the serial communication procedures, including PC and single-chip, single PC dual serial communication, PC and PC serial communication.
labview-to-PC
- labview实现PC 与单片机通信，任务要求：PC机发送数据给单片机，然后单片机返回发送的数据，测试发送的数据和接收的数据是否相同。波特率：4800，数据位8，校验位：0，停止位：1-labview achieve PC to communicate with the microcontroller, mission requirements: PC sends data to the microcontroller, then microcontroller returns data tra
ceshi2
- 上位机与单片机通过串口通信，可以通过usb转232实现-Through the serial communication between the microcontroller and PC
2017010716500
- lanbiew串口通信程序，实现PC与51单片机串口通信-Lanbiew serial communication program, PC and 51 single-chip serial communication
串口程序
- 实现上位机与单片机的串口调试，pc输入一条数据，单片机读取数据后并返回上位机(Realization of serial debugging of host computer and single chip microcomputer)
Labview
- 利用LabWindowsCVI实现PC与单片机数字量输入 利用LabVIEW实现PC与单片机数字量输出 利用LabWindowsCVI实现PC与单片机数字量输出(Using LabWindowsCVI to realize digital input of PC and single chip microcomputer Using LabVIEW to realize digital output of PC and single chip microcomputer Using La
labview PC通信与单片机测控
- labview PC通信与单片机测控 书籍源码基础资料(LabVIEW PC communication and SCM control book source data, basic information.)