搜索资源列表
pathloss&gnoise
- cp0801_pathloss为UWB信道损耗计算函数，利用a=(c/(d^gamma))计算出信道增益，然后对函数的输入信号幅度进行变换得到输出结果。 cp0801_Gnoise1和cp0801_Gnoise2为产生AWGN的函数，分别为Eb/No和Ex/No条件下AWGN的产生-cp0801_pathloss for UWB channel depletion calculation function, use a = (c / (d ^ gamma)) calculated Chann
DS_uwbprogram
- 关于simu1: 在simlink运行之前的初始化过程中，完成了信道时延和幅度的估计，多径合成权系数估计 多径合成采用可选EG/MR/MMSE合成 信道可选白噪声信道AWGN和IEEE80.215.3a UWB标准信道模型(CM1-CM4)但为了简化， 这里采用了IEEE80.215.3a给出了信道模型中的仿真数据包(如果你是作超宽带的，信道模型程序和数据可从IEEE80.215.3a网站获取) 和大部分仿真一样，模型中的Eb/No指的是单比特信息符号携带的能量和噪声的比例，
mimo-EbNo-BER
- mimo系统仿真 bpsk调制 瑞利信道 得Eb/No-BER曲线-mimo system simulation bpsk Rayleigh channel modulation in Eb / No-BER curves
finalreport
- matlab实现的多个基础程序和报告并有流程图（1） 绘出正弦信号波形及频谱。 （2） 单极性归零（RZ）波形及其功率谱，占空比为50％。 （3） 升余弦滚降波形的眼图及其功率谱。滚降系数为0.5。发送码元取值为0、2。 （4） 最佳基带系统的Pe~Eb\\No曲线，升余弦滚降系数a=0.5，取样值的偏差是Ts/4。 （5） Pe~Eb\\No，升余弦滚降系数a=0.5，取样时间无偏差，但信道是多径信道，C(f)=abs(1-0.5*exp(-j*2*pi
eqber_adaptive
- This scr ipt runs a simulation loop for either a linear or a DFE equalizer. It uses the RLS algorithm to initially set the weights, then uses LMS thereafter to minimize execution time. It plots the equalized signal spectrum, then generates and plot
ebno
- Eb/No calculation code
BPSK
- the BPSK signal generation and additive gaussian noise channel simulation. the result is ebno. this file is source code using matlab.
Task2new
- This prorgam calculates Bit error rate on awgn channel with a particular Eb/No values and plot the graph of BEP(Bit Error Probability) against Eb/No.
QAM_Eb_No_SER
- calculate the theoretical exact(in AWGN) SYMBOL ERROR RATE(Ps_SER) verses Eb/No for even numbers of bits per symbol in qam modulation
multipath_code
- 设计一完整的移动通信系统物理层传输方案 (WiMAX场景)： 试设计一完整的移动通信系统物理层传输方案并用MATLAB程序实现，要求满足以下指标： 1. 数据速率：5km/hr的移动速度下可实现60Mbps，同时在120km/hr的移动速度下可实现10Mbps，且Eb/No小于20dB时可实现误比特率Pe <= 10-4 2. 信号带宽为20MHz，工作在2GHz频带 3. 信道模型: COST207模型的6径瑞利信道(可参考程序 multipath_code.zip)
7456
- Besides calculating the SER verses Eb/No for the various levels of QAM, The m-file shows the coding gain required to closely approach Shannon s channel capacity limit for 4QAM,16QAM,64QAM,256QAM and 1024QAM. Notes are given at the end of the m-file
bpsk
- BPSK在AWGN信道下,不同的采样率下不同的EB/NO的误码率仿真-failed to translate
mfsk
- MFSK不同进制下，在不同采样率不同EB/NO时的误码率分析-MFSK under different band, different at different sampling rates EB/NO when the error rate analysis
mpsk_table
- This MATLAB Code plot BER Vs Eb/No for M_ary PSK with different values of M. The user can choose the desired BER and the code will tell what is the required Eb/No to achieve this BER for different values of M. In addition, a plot for shannon limit is
mfsk_table
- This MATLAB Code plot the BER Vs Eb/No for M_ary FSK for differnt values of M. The user can choose the desired BER and the code will tell what is the required Eb/No to achieve this BER for differnt values of M. In addition, a plot of the shannon limi
mimo66
- mimo code for ofdm.ber vs eb/no
MIMo
- mimo code for ofdm.ber vs eb/no
mimo1
- mimo code for ofdm.ber vs eb/no
mimotools
- mimo code for ofdm.ber vs eb/no
mimo77_org
- mimo code for ofdm.ber vs eb/no