搜索资源列表
led
- 使用F2812开发的液晶控制程序，并包含有完整的实验组件！
F2812_Gpio
- F2812 GPIO控制LED灯亮1s，灭1s。（CCS3.3开发环境）-F2812 GPIO control LED lights 1s, OFF 1s. (CCS3.3 Development Environment)
SourceCode19_PWMDCMOT
- f2812下电机驱动范例程序，C语言编写-f2812 procedures under the motor drive example, C language
gpio_flash
- DSP F2812 LED灯闪烁实验FLASH烧写程序-DSP F2812 LED lights flashing experimental procedures FLASH programmer
main
- DSP-f2812 led流水灯实验代码-DSP-f2812
lab0402-Ledarray
- F2812中led阵列的控制，学习的好材料-F2812 led array in the control, good learning materials
F2812_SPI
- F2812 SPI （CCS3.3开发环境下）实验说明:主要硬件部分：DSP，74HC595（串入并出的移位器),共阳数码管。SPIMOSI和SPICLK直接从DSP接到了74HC595的SER和SRCLK，作为数据和时钟信号的输入，SPISTE引脚接到了74HC595的RCLK以控制其选通。 实验结果:可看到数码管从0～F循环显示-F2812 SPI experiment shows: The main hardware components: DSP, 74HC595 (serial shi
F2812_LedFlash
- F2812 利用定时器CpuTimer0中断，实现LED亮1s，灭1s。 （CCS3.3开发环境下） 功 能：通过使用CPU定时器来控制LED D3的亮和灭 说 明：D3与引脚XF相连，XF为低电平时，D3亮；XF为高电平时，D3灭。频率为1Hz，即每隔1s钟，D3被点亮。间隔时间由CpuTimer0来控制。-F2812 using timer interrupt CpuTimer0, the LED light 1s, off 1s. Features: CPU timer to contro
led.c
- DSP F2812 EVM板上LED灯的控制方法。-Control LED light on DSP F2812 EVM board
MyProjects
- ICETEK－F2812-A评估板及教学实验箱实验参考程序，包括LED，AD，SCI,Demotor,PWM,fft,fir ,iir,KEY等例程-ICETEK-F2812-A evaluation board and teaching experimental box experiment reference program, including LED, AD, SCI, Demotor, PWM, fft, fir, iir, KEY and other routine
SourceCode01_Timer0
- F2812跑马灯程序，通过周期定时使得led灯循环显示，是DSP初学者必备-F2812 Marquee program, through the cycle timed loop makes the led light display, is essential DSP beginners
source
- 本程序采用F2812作为控制器，实现6个小led灯一次亮灭，使用GPIOA0-A5输出口-The program uses F2812 as a controller, 6 small led lights to achieve a light off, use GPIOA0-A5 output port
EX01_GPIO_LED
- DSP经典入门例程，GPIO流水灯实验，F2812芯片，循环点亮GPIOA的灯，时间间隔为300ms。-DSP F2812 source code ，GPIO led experiment.
EX02_CpuTimer0
- DSP经典入门例程，timer0定时器中断控制流水灯实验，F2812芯片，循环点亮和熄灭LED，时间间隔为1s。-DSP classic Tutorial，about how to enable timer 0 to control the led light and mute.
LED_flash
- F2812 DSP LED_flash点亮LED灯程序源码-F2812 DSP LED_flash program
GpioToggle
- 该程序主要是用f2812来点亮LED灯。其中程序中采用了3种方式对Gpio进行操作。-The program is mainly to light LEDs lamp by f2812. Which the program uses three kinds of ways Gpio operation.
1-GPIO_LED
- 数字信号处理器F2812程序,LED流水灯，编程时参考。-F2812 digital signal processor program, LED water lights, the programming reference.
ICETEK-F2812-B-v1.1
- 测试DSP2812的XF引脚，控制LED灯的闪烁-To test the XF pin DSP2812, control LED lights flashing
dsp--for-led
- 应用f2812基于dsp的led显示,通过在ccs平台上的安装，最后烧结到外部存储器实现自动化-dsp for led
Ex06_POP28335_PWM_LED
- PWM drives the led light.