搜索资源列表
avr-gcc-display-led-num.move
- avr-gcc编写的数字移位显示程序,使用AVR单片机，avr studio编译环境下编译通过。-avr - gcc prepared by the displacement figures show, the use of AVR, avr studio compiler environment compile.
DLED
- 实验芯片： ATmega8515L或Atmega8515 工作频率： 8MHz 编译软件： C语言：WINAVR 1.41 汇编语言：AVR Studio 功能： 8个数码管从左至右依次显示：1，2，3，4，5，6，7，8。 -Experimental chip: ATmega8515L or Atmega8515 frequency: 8MHz compiler software: C language: WINAVR 1.41 asse
SetLED_WinCE6
- Simple project for set LED on Windows CE 6. Compiled with Visual studio 2008.
swled_asm
- This program is written in Assembly language for AVR Microcontrollers. It is to be compiled witn AVR Studio is available for Free. The Program is for learning and using input and output ports of AVR using Switches and LED s for inputting and outputin
iictansmitandrendbyte
- atmega16 twi(iic)接口发送数据到AT24C32,再从AT24C32读出数据，并用读出的数据点亮LED灯，用AVR studio编写-atmega16 communicate with AT24C32 through twi(iic) bus
led
- 基于Code Composer Studio软件的DSP指示灯程序-Code Composer Studio software-based DSP indicator program
atmega
- 通过winavr+AVR Studio编程，实现了两个Atmega16单片机的RS232通信。包括矩阵键盘检测与LED动态显示。-By winavr+ AVR Studio programming, two Atmega16 MCU RS232 communication. Including the detection and LED matrix dynamic keyboard display.
FashionUI
- LED 顯示元件 包含圓形LED及方形LED可控制閃爍及開關 包含測試專案 visual studio 2010-Led UI Component include flash LED and OnOff LED
knightrider
- Microcontroller Arduino Duemilanove programmed in C via AVR Studio 4 with a running LED like the car of Michael Knigth (TVserial)
PWMshuchukongzhiLED
- 艾米电子工作室的，用PWM输出控制LED显示，详细的程序讲解和步骤可以是大家进一步学习FPGA-Amy electronic studio, with the PWM output control LED display, detailed procedures and steps can you explain further learning FPGA
led_c
- This program is used for blinking leds with different frequencies. A DSP processor is connected to the computed system and CCS studio interface software should be available. Four LEDs are available on the processor kit. This program makes the 1st LED
ProjectLab3Timer
- program Led 3 Timer open it use AVR Studio
Embedded-Pak-Agus
- This source code how to make running LED using Atmega16 on avr studio 4-This is source code how to make running LED using Atmega16 on avr studio 4
hid
- 此文件是百合电子工作室推出的USB开源项目：Easy USB 51 Programer的一部分。 Easy USB 51 Programer 是一个多功能的USB学习板（USB接口 芯片采用philips的pdiusbd12），通过此项目，您不仅可以学习到 USB HID设备类的开发（包括下位机固件驱动的编写和上位机应用 程序的编写），还可以学习UB的其它标准设类（如USB Mass Storage）及自定义的非标准设备类的开发。Easy U
1_LED
- LED灯实验。1．在ICCAVR环境下建立项目，并加入源文件，然后编译、连接该项目 2．用AVR Studio仿真（需选择JTAG ICE仿真）或者将LED.HEX烧入单片机 3．程序默认的是流水灯，当把源程序的i=0改为i=1时，LED将以闪烁灯显示-LED light experiment.A. , Establish project ICCAVR environment, and adding a source file and then compile the project
LED
- mega 1284 实现流水灯代码 avr studio 带Proteus仿真。-mega 1284 LED avr studio Proteus Simulation
AVR-Studio
- ATMEGA16 AVR单片机，LED闪烁实验测试程序，流水灯-GCC AVR Studio development environment under routine
C#led灯的控制
- Microsoft Visual Studio C# 控制报警灯串口通讯 论文,(C# control alarm lamp)
Digispark-LED
- 全部文件打包。用atmel studio 7编写，驱动digispark(attiny85核心)PB1所接的LED以5Hz闪烁。(The program is written in Atmel Studio 7, and the leds connected to the digispark(attiny85 core)PB1 are flashing with 5Hz.)
lab1-GPIO_output_LED
- Code Compose Studio,GPIO输出点亮LED灯(Code Compose Studio GPIO output LED)