搜索资源列表
GPIO
- 在万利199元开发板上实现了STM32的操作，控制LED闪烁。-199 yuan in Wanli STM32 development board implements the operation, control LED flashes.
LED
- 基于STM32下，在IAR环境下，自己编写的中断控GPIO的LED灯的源码。-Based on the STM32, the environment in the IAR, write your own interrupt control the LED light source GPIO.
STM32-ucos
- stm32芯片 KERIL 3.0 ucosii 功能实现： GPIO LED测试 STM32 USB部分驱动数据-stm32 chip KERIL 3.0 ucosii function realization: GPIO LED Test STM32 USB part of the driver data
GPIO_RVMDK
- 本源码为STM32的GPIO使用例程,主要演示GPIO的使用。开发环境realviewMDK。 程序通过按键对应的引脚的电平是否被拉低来判断按键是否被按下，如果按键被按下，则相应的LED闪烁一次。-The source code for the STM32' s GPIO use of routine, the main demonstration GPIO use. Development environment realviewMDK. Program through the bu
GPIO-LED-V1.0_OK
- stm32学习板开发材料，控制LED灯的连续开关闭。-stm32 learning board development materials, control LED lights continuously open to close.
GPIO-LED-V1.0_OK
- 芯达 STM32 GPIO 测试 希望对大家有帮助-STM32 GPIO core of the test we want to help
STM32-7SEG-LED-SCAN
- 8位数码管动态扫描显示实验(显示不用库函数) *显示用指针直接访问GPIO端口的输出寄存器，形式GPIOD->ODR *延时delay_nms(5)时，显示不闪烁 *74HC138 A--P2.2--PE.0 B--P2.3--PE.1 C--P2.4--PE.2 *74HC573 D0~D7---PD[0..7] LE---PE.3 *by 追梦 2011-4-3-8-bit digital dynamic scan showed that the experimen
2-LED
- stm32单片机实验，通过GPIO控制LED，流水灯经典实验-STM32 MCU experimental, controlled by GPIO LED, light classical experiment
GPIO_LED
- 通用IO口的详细例程代码及相关注释 方便的很-stm32 GPIO LED
F2XX--GPIO
- STM32的GPIO口编写的LED闪烁程序，方便大家熟悉操作环境和方法。KEIL环境。-STM32 GPIO port LED flashes written procedures to facilitate the familiar operating environment and methods. KEIL environment.
GPIO-LED-V1.0_OK
- STM32 GPIO LED OK OK BOARD-STM32 GPIO LED OK OK BOARD
GPIO-LED-V1.0_OK
- 基于STM32 的端口基本设置程序，很基础的东西-Based on the STM32 port basic setup, very basic things
GPIO-LED
- 基于STM32的开发板测试程序，很好用的-Based on the STM32 development board testing procedures, very useful
GPIO-LED
- STM32驱动LED程序,使用系统滴答定时器精确延时。-STM32 LED driver, the use of the system timer tick precision delay。
stm32f030f4p6_Key_LED_Interrupt
- Initialize Key buttons and GPIO with interrupt framework by stm32f030f4p6
实验1：LED闪烁
- 1.STM32 GPIO管脚配置 2.点亮发光二极管(1.STM32 GPIO pin configuration 2. Light the light emitting diode)
12-GPIO输出—使用固件库点亮LED灯
- STM32点亮LED灯2313122332(The HA is according to the time of the story of the world)
1、LED
- 流水灯，对于GPIO口的配置和利用，使得led灯逐个点亮(Flow lamp For the configuration and use of the GPIO port, the LED lights are lit by one by one)
GPIO
- 使用stm32的gpio的引脚5通过中断法最终实现led灯的点亮。(Use the STM32 pin 5 to light the LED lamp.)
STM32F103 GPIO点亮LED灯程序
- STM32 的GPIO操作示例程序代码, 试用与Keile环境STM32F103代码(STM32 GPIO operation code)