搜索资源列表
uart from opencores
- 用VHDL实现串口 可以实现与pc机的通信 收发 中断都可以 效果比较好-VHDL implement serial port, it can communicate with pc, it can accept and send message, and it can be interrupted.
uart.rar
- 实现串并口通信,共有发送和接受两个模块。,Strings parallel to achieve communication, send and receive a total of two modules.
uart8.zip
- 使用Libero提供的异步通信IP核实现UART通信，并附带仿真程序。UART设置为1位开始位，8位数据位，1位停止位，无校验。且UART发送自带2级FIFO缓冲，占用FPGA面积很小。,Libero provided the use of asynchronous communication IP core implementation UART communications, and incidental simulation program. UART is set to 1 to sta
UART
- 自己实用Verilog编写的UART程序，1位开始位，8位数据位，1位停止位，本测试程序配置完管脚后，实用串口大师发送数据，则返回数据为发送数据+1-Verilog prepared their own UART practical procedures to start a bit, 8 data bits, 1 stop bit, the test procedure End pin configuration, the utility serial Master to send data,
Uart_Send
- UART的完整发送程序，包括完整的工程核源代码。-UART to send the complete procedure, including the complete source code of nuclear engineering.
UART
- 内含有完整的UART代码，包括发送和接受，且有testbench，可以直接仿真调试-Contain complete UART code, including send and receive and there testbench, can directly Simulation debugging
uart_zhiwen
- RS232的UART编程，包括波特率发生器模块，串口接受模块，串口发送模块-RS232 programming the UART, including the baud rate generator module, serial module to receive, send serial module
uart
- uart send resive module
my_uart_top
- 实现的功能如题，就是FPGA里实现从PC接收数据，然后把接收到的数据发回去。使用的是串口UART协议进行收发数据。上位机用的是老得掉牙的串口调试助手-To achieve the functions such as title, that is, to achieve FPGA receives data from the PC, and then receive data back fat. Using a UART serial port protocol to send and recei
s7enable_send0x55_UART_9600
- 最简单的UART发送程序，vhdl编写，系统时钟40M，波特率9600，外Load有效（一个高脉冲）即向PC发送一个字节0X-UART to send the simplest procedures, vhdl prepared, the system clock 40M, baud rate 9600, outside the Load effective (a high-pulse) to the PC sends a byte 0X55
uart_test_ok_921
- 一个简单的uart 源码，接收一个字符并发回，通过测试，可以使用的，输入时钟12mhz,发送速率96-A simple uart source code, receiving a character and send back through the test, can be used, input clock 12mhz, sending rate 9600
uart_0910
- uart串口传输的verilog RTL级源码，已通过仿真验证。文件主要包含发送、接受位处理，发送、接受字节帧处理，对学习串口通信的朋友很有帮助-uart serial transmission verilog RTL-level source code has been verified by simulation. File mainly contains the send, receive digital processing, sending, receiving bytes of fr
aima
- 基于DMA通过UART发送和接收数据的例子，注意DMA_0为接受通道，DMA_1为发送通道。当然可以将dma的read_master和writer_master同时连在uart_0和sdram_0的从端口上，这样是可以用一个dma对两者读写操作，但是不能同时做双向传输。-Based on DMA send and receive data through the UART example, attention DMA_0 accepted channels, DMA_1 to send the
uart16
- 一个16位的uart，可以实现串行通信，接受或者发送数据！-A 16-bit uart, serial communication can be achieved, accept or send data!
UART
- VHDL语言写的串口发送、接收程序，根据晶振和相应的波特率修改分频器就可以实现！-Written in VHDL serial send, receive, process, according to crystal and the corresponding baud rate divider changes can be achieved!
uart
- 串行异步收发接口，简称UART，是一种广泛应用的串行传输接口。这是用vhdl实现的程序，将UART分成相应的几个模块，并用顶层文件进行模块化设计。-Send and receive asynchronous serial interface, referred to as the UART, is a widely used serial transmission interface. This is achieved using vhdl procedure to the appropriat
FPGA_UART
- 用Verilog语言实现的FPGA UART独立收发模块 思路简单，代码简洁。在Lattice LFE3EA VERSA开发板上验证通过,编译器Lattice Diamond. 功能：串口收到数据后立即回传，此后每一秒串口数据+1再发送。-Using Verilog language independent of FPGA UART transceiver idea is simple, concise code. Development board in Lattice LFE3EA
uart
- 用VHDL实现UART通讯（暂时只能发送）-UART communication using VHDL (temporarily only send)
xmtr
- 运用VHDL语言，实现串口的发送子程序，可以将该模块直接套入主程序。-VHDL UART SEND
teacher_uart
- 由verilog编写的uart收发模块，能够在串口助手发送字符，并在数码管上显示，开发板为basys3 内置约束文件(The UART transceiver module written by Verilog can send characters to serial assistant and display them on the digital tube. the development board is built-in constraint file of basys3)